mirror of
https://github.com/Proxmark/proxmark3.git
synced 2024-11-11 09:59:45 +08:00
30f2a7d38f
typo fixes in iso14443a code, added the missing "tools" directory, added initial elements for online/offline detection for commands.
232 lines
8.6 KiB
C
232 lines
8.6 KiB
C
//-----------------------------------------------------------------------------
|
|
// Routines to load the FPGA image, and then to configure the FPGA's major
|
|
// mode once it is configured.
|
|
//
|
|
// Jonathan Westhues, April 2006
|
|
//-----------------------------------------------------------------------------
|
|
#include <proxmark3.h>
|
|
#include "apps.h"
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Set up the Serial Peripheral Interface as master
|
|
// Used to write the FPGA config word
|
|
// May also be used to write to other SPI attached devices like an LCD
|
|
//-----------------------------------------------------------------------------
|
|
void SetupSpi(int mode)
|
|
{
|
|
// PA10 -> SPI_NCS2 chip select (LCD)
|
|
// PA11 -> SPI_NCS0 chip select (FPGA)
|
|
// PA12 -> SPI_MISO Master-In Slave-Out
|
|
// PA13 -> SPI_MOSI Master-Out Slave-In
|
|
// PA14 -> SPI_SPCK Serial Clock
|
|
|
|
// Disable PIO control of the following pins, allows use by the SPI peripheral
|
|
PIO_DISABLE = (1 << GPIO_NCS0) |
|
|
(1 << GPIO_NCS2) |
|
|
(1 << GPIO_MISO) |
|
|
(1 << GPIO_MOSI) |
|
|
(1 << GPIO_SPCK);
|
|
|
|
PIO_PERIPHERAL_A_SEL = (1 << GPIO_NCS0) |
|
|
(1 << GPIO_MISO) |
|
|
(1 << GPIO_MOSI) |
|
|
(1 << GPIO_SPCK);
|
|
|
|
PIO_PERIPHERAL_B_SEL = (1 << GPIO_NCS2);
|
|
|
|
//enable the SPI Peripheral clock
|
|
PMC_PERIPHERAL_CLK_ENABLE = (1<<PERIPH_SPI);
|
|
// Enable SPI
|
|
SPI_CONTROL = SPI_CONTROL_ENABLE;
|
|
|
|
switch (mode) {
|
|
case SPI_FPGA_MODE:
|
|
SPI_MODE =
|
|
( 0 << 24) | // Delay between chip selects (take default: 6 MCK periods)
|
|
(14 << 16) | // Peripheral Chip Select (selects FPGA SPI_NCS0 or PA11)
|
|
( 0 << 7) | // Local Loopback Disabled
|
|
( 1 << 4) | // Mode Fault Detection disabled
|
|
( 0 << 2) | // Chip selects connected directly to peripheral
|
|
( 0 << 1) | // Fixed Peripheral Select
|
|
( 1 << 0); // Master Mode
|
|
SPI_FOR_CHIPSEL_0 =
|
|
( 1 << 24) | // Delay between Consecutive Transfers (32 MCK periods)
|
|
( 1 << 16) | // Delay Before SPCK (1 MCK period)
|
|
( 6 << 8) | // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud
|
|
( 8 << 4) | // Bits per Transfer (16 bits)
|
|
( 0 << 3) | // Chip Select inactive after transfer
|
|
( 1 << 1) | // Clock Phase data captured on leading edge, changes on following edge
|
|
( 0 << 0); // Clock Polarity inactive state is logic 0
|
|
break;
|
|
case SPI_LCD_MODE:
|
|
SPI_MODE =
|
|
( 0 << 24) | // Delay between chip selects (take default: 6 MCK periods)
|
|
(11 << 16) | // Peripheral Chip Select (selects LCD SPI_NCS2 or PA10)
|
|
( 0 << 7) | // Local Loopback Disabled
|
|
( 1 << 4) | // Mode Fault Detection disabled
|
|
( 0 << 2) | // Chip selects connected directly to peripheral
|
|
( 0 << 1) | // Fixed Peripheral Select
|
|
( 1 << 0); // Master Mode
|
|
SPI_FOR_CHIPSEL_2 =
|
|
( 1 << 24) | // Delay between Consecutive Transfers (32 MCK periods)
|
|
( 1 << 16) | // Delay Before SPCK (1 MCK period)
|
|
( 6 << 8) | // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud
|
|
( 1 << 4) | // Bits per Transfer (9 bits)
|
|
( 0 << 3) | // Chip Select inactive after transfer
|
|
( 1 << 1) | // Clock Phase data captured on leading edge, changes on following edge
|
|
( 0 << 0); // Clock Polarity inactive state is logic 0
|
|
break;
|
|
default: // Disable SPI
|
|
SPI_CONTROL = SPI_CONTROL_DISABLE;
|
|
break;
|
|
}
|
|
}
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Set up the synchronous serial port, with the one set of options that we
|
|
// always use when we are talking to the FPGA. Both RX and TX are enabled.
|
|
//-----------------------------------------------------------------------------
|
|
void FpgaSetupSsc(void)
|
|
{
|
|
// First configure the GPIOs, and get ourselves a clock.
|
|
PIO_PERIPHERAL_A_SEL = (1 << GPIO_SSC_FRAME) |
|
|
(1 << GPIO_SSC_DIN) |
|
|
(1 << GPIO_SSC_DOUT) |
|
|
(1 << GPIO_SSC_CLK);
|
|
PIO_DISABLE = (1 << GPIO_SSC_DOUT);
|
|
|
|
PMC_PERIPHERAL_CLK_ENABLE = (1 << PERIPH_SSC);
|
|
|
|
// Now set up the SSC proper, starting from a known state.
|
|
SSC_CONTROL = SSC_CONTROL_RESET;
|
|
|
|
// RX clock comes from TX clock, RX starts when TX starts, data changes
|
|
// on RX clock rising edge, sampled on falling edge
|
|
SSC_RECEIVE_CLOCK_MODE = SSC_CLOCK_MODE_SELECT(1) | SSC_CLOCK_MODE_START(1);
|
|
|
|
// 8 bits per transfer, no loopback, MSB first, 1 transfer per sync
|
|
// pulse, no output sync, start on positive-going edge of sync
|
|
SSC_RECEIVE_FRAME_MODE = SSC_FRAME_MODE_BITS_IN_WORD(8) |
|
|
SSC_FRAME_MODE_MSB_FIRST | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0);
|
|
|
|
// clock comes from TK pin, no clock output, outputs change on falling
|
|
// edge of TK, start on rising edge of TF
|
|
SSC_TRANSMIT_CLOCK_MODE = SSC_CLOCK_MODE_SELECT(2) |
|
|
SSC_CLOCK_MODE_START(5);
|
|
|
|
// tx framing is the same as the rx framing
|
|
SSC_TRANSMIT_FRAME_MODE = SSC_RECEIVE_FRAME_MODE;
|
|
|
|
SSC_CONTROL = SSC_CONTROL_RX_ENABLE | SSC_CONTROL_TX_ENABLE;
|
|
}
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Set up DMA to receive samples from the FPGA. We will use the PDC, with
|
|
// a single buffer as a circular buffer (so that we just chain back to
|
|
// ourselves, not to another buffer). The stuff to manipulate those buffers
|
|
// is in apps.h, because it should be inlined, for speed.
|
|
//-----------------------------------------------------------------------------
|
|
void FpgaSetupSscDma(BYTE *buf, int len)
|
|
{
|
|
PDC_RX_POINTER(SSC_BASE) = (DWORD)buf;
|
|
PDC_RX_COUNTER(SSC_BASE) = len;
|
|
PDC_RX_NEXT_POINTER(SSC_BASE) = (DWORD)buf;
|
|
PDC_RX_NEXT_COUNTER(SSC_BASE) = len;
|
|
PDC_CONTROL(SSC_BASE) = PDC_RX_ENABLE;
|
|
}
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Download the FPGA image stored in flash (slave serial).
|
|
//-----------------------------------------------------------------------------
|
|
void FpgaDownloadAndGo(void)
|
|
{
|
|
// FPGA image lives in FLASH at base address 0x2000
|
|
// The current board design can not accomodate anything bigger than a XC2S30
|
|
// FPGA and the config file size is fixed at 336,768 bits = 10,524 DWORDs
|
|
const DWORD *FpgaImage=((DWORD *)0x2000);
|
|
const DWORD FpgaImageLen=10524;
|
|
|
|
int i, j;
|
|
|
|
PIO_OUTPUT_ENABLE = (1 << GPIO_FPGA_ON);
|
|
PIO_ENABLE = (1 << GPIO_FPGA_ON);
|
|
PIO_OUTPUT_DATA_SET = (1 << GPIO_FPGA_ON);
|
|
|
|
SpinDelay(50);
|
|
|
|
LED_D_ON();
|
|
|
|
HIGH(GPIO_FPGA_NPROGRAM);
|
|
LOW(GPIO_FPGA_CCLK);
|
|
LOW(GPIO_FPGA_DIN);
|
|
PIO_OUTPUT_ENABLE = (1 << GPIO_FPGA_NPROGRAM) |
|
|
(1 << GPIO_FPGA_CCLK) |
|
|
(1 << GPIO_FPGA_DIN);
|
|
SpinDelay(1);
|
|
|
|
LOW(GPIO_FPGA_NPROGRAM);
|
|
SpinDelay(50);
|
|
HIGH(GPIO_FPGA_NPROGRAM);
|
|
|
|
for(i = 0; i < FpgaImageLen; i++) {
|
|
DWORD v = FpgaImage[i];
|
|
for(j = 0; j < 32; j++) {
|
|
if(v & 0x80000000) {
|
|
HIGH(GPIO_FPGA_DIN);
|
|
} else {
|
|
LOW(GPIO_FPGA_DIN);
|
|
}
|
|
HIGH(GPIO_FPGA_CCLK);
|
|
LOW(GPIO_FPGA_CCLK);
|
|
v <<= 1;
|
|
}
|
|
}
|
|
|
|
LED_D_OFF();
|
|
}
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Send a 16 bit command/data pair to the FPGA.
|
|
// The bit format is: C3 C2 C1 C0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
|
|
// where C is the 4 bit command and D is the 12 bit data
|
|
//-----------------------------------------------------------------------------
|
|
void FpgaSendCommand(WORD cmd, WORD v)
|
|
{
|
|
SetupSpi(SPI_FPGA_MODE);
|
|
while ((SPI_STATUS & SPI_STATUS_TX_EMPTY) == 0); // wait for the transfer to complete
|
|
SPI_TX_DATA = SPI_CONTROL_LAST_TRANSFER | cmd | v; // send the data
|
|
}
|
|
//-----------------------------------------------------------------------------
|
|
// Write the FPGA setup word (that determines what mode the logic is in, read
|
|
// vs. clone vs. etc.). This is now a special case of FpgaSendCommand() to
|
|
// avoid changing this function's occurence everywhere in the source code.
|
|
//-----------------------------------------------------------------------------
|
|
void FpgaWriteConfWord(BYTE v)
|
|
{
|
|
FpgaSendCommand(FPGA_CMD_SET_CONFREG, v);
|
|
}
|
|
|
|
//-----------------------------------------------------------------------------
|
|
// Set up the CMOS switches that mux the ADC: four switches, independently
|
|
// closable, but should only close one at a time. Not an FPGA thing, but
|
|
// the samples from the ADC always flow through the FPGA.
|
|
//-----------------------------------------------------------------------------
|
|
void SetAdcMuxFor(int whichGpio)
|
|
{
|
|
PIO_OUTPUT_ENABLE = (1 << GPIO_MUXSEL_HIPKD) |
|
|
(1 << GPIO_MUXSEL_LOPKD) |
|
|
(1 << GPIO_MUXSEL_LORAW) |
|
|
(1 << GPIO_MUXSEL_HIRAW);
|
|
|
|
PIO_ENABLE = (1 << GPIO_MUXSEL_HIPKD) |
|
|
(1 << GPIO_MUXSEL_LOPKD) |
|
|
(1 << GPIO_MUXSEL_LORAW) |
|
|
(1 << GPIO_MUXSEL_HIRAW);
|
|
|
|
LOW(GPIO_MUXSEL_HIPKD);
|
|
LOW(GPIO_MUXSEL_HIRAW);
|
|
LOW(GPIO_MUXSEL_LORAW);
|
|
LOW(GPIO_MUXSEL_LOPKD);
|
|
|
|
HIGH(whichGpio);
|
|
}
|