mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2025-02-01 21:08:18 +08:00
Iceman
GitHub
commit
3c4044111f
1 changed files with 71 additions and 70 deletions
|
|
@ -24,17 +24,17 @@
|
|||
|
||||
## Introduction
|
||||
|
||||
The T5577 is a generic LF (Low Frequency) RFID card the is used in the
|
||||
The T5577 is a generic LF (Low Frequency) RFID card that is used in the
|
||||
125 Khz frequency space. It is a good card to use to learn about RFID and
|
||||
learn how to use the proxmark3.
|
||||
|
||||
It is highly recommend that when learning about RFID that learning how
|
||||
It is highly recommended that when learning about RFID that learning how
|
||||
to read the data sheets be near the top of the list. It can be very hard
|
||||
as the data sheet will hold the information you need, but you don’t yet
|
||||
know what it means. As such, I will attempt to point to sections of the
|
||||
data sheet and would highly advise that you look at the data sheet as
|
||||
you go. Overtime the data sheet may change, as a result things may not
|
||||
always be reference correctly.
|
||||
always be referenced correctly.
|
||||
|
||||
As at writing this guide, the data sheet can be found at :
|
||||
|
||||
|
|
@ -64,9 +64,9 @@ the chip how to behave.
|
|||
|
||||
## What data is on my T5577
|
||||
|
||||
Let’s have a look and see what a card might look in the proxmark3
|
||||
Let’s have a look and see what a card might look like in the proxmark3
|
||||
software. Since we can change the configuration of how the T5577 will
|
||||
output data, the proxmark3 software need to work out how to interpreted
|
||||
output data, the proxmark3 software needs to work out how to interpret
|
||||
the data it receives, we do this with the following command.
|
||||
|
||||
It should be noted that the T5577 has many clones. As such the default
|
||||
|
|
@ -102,20 +102,20 @@ Your results should look similar to the following:
|
|||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 02 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 04 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 05 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 06 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 07 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 04 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 05 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 06 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 07 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] Reading Page 1:
|
||||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | E0150A48 | 11100000000101010000101001001000 | ...H
|
||||
[+] 02 | 2D782308 | 00101101011110000010001100001000 | -x#.
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
```
|
||||
I will cover the meaning of this data as we go, but for now, lets keep
|
||||
it simple.
|
||||
|
|
@ -126,7 +126,7 @@ The basic function of using the proxmark3 with rfid cards is to read and
|
|||
write data. This reading and writing must be done in the correct way
|
||||
needed for the chip (and its configuration). Lucky for us, the
|
||||
developers have done a great job and gave us commands. What we need to
|
||||
know is that with the T5577 data is read/written one complete block at a
|
||||
know is that with the T5577, data is read/written one complete block at a
|
||||
time. Each block holds 32 bits of data (hence the binary output shown)
|
||||
|
||||
Since we know that the card has data and configuration blocks, lets say
|
||||
|
|
@ -150,14 +150,14 @@ can see the card)
|
|||
[+] Reading Page 0:
|
||||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 01 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
```
|
||||
Note: Depending on the history of your card your data may vary, but
|
||||
Note: Depending on the history of your card, your data may vary, but
|
||||
should match the dump data.
|
||||
|
||||
2) Write some new data into block 1 on the card.
|
||||
|
||||
We use the d option to supply the data ‘12345678’
|
||||
We use the -d option to supply the data ‘12345678’
|
||||
```
|
||||
[usb] pm3 --> lf t55xx write -b 1 -d 12345678
|
||||
```
|
||||
|
|
@ -177,8 +177,8 @@ can see the card)
|
|||
[+] 01 | 12345678 | 00010010001101000101011001111000 | .4Vx
|
||||
```
|
||||
4) The data is written in Hexadecimal. A single hex digit holds 4 bits
|
||||
of data. So to store 32 bits in a block we need to supply 8 hex
|
||||
digits (8 \* 4 = 32). If you are familiar with hex and binary do a
|
||||
of data. So to store 32 bits in a block, we need to supply 8 hex
|
||||
digits (8 \* 4 = 32). If you are not familiar with hex and binary do a
|
||||
little bit of home work to learn. The following is a quick start.
|
||||
|
||||
| Hex | Binary | Decimal |
|
||||
|
|
@ -238,31 +238,34 @@ result:
|
|||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | 89ABCDEF | 10001001101010111100110111101111 | ....
|
||||
[+] 02 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 04 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 05 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 06 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 07 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 04 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 05 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 06 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 07 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] Reading Page 1:
|
||||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | E0150A48 | 11100000000101010000101001001000 | ...H
|
||||
[+] 02 | 2D782308 | 00101101011110000010001100001000 | -x#.
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
```
|
||||
|
||||
Practice reading and writing to blocks 1 to 7 until you are happy you
|
||||
Practice reading and writing to blocks 1 to 6 until you are happy you
|
||||
can do it and get the results you wanted (i.e. the data you want stored
|
||||
is written to the block you want it stored in).
|
||||
is written to the block you want it stored in). I recommend staying
|
||||
away from block 7 as this is where the password is stored, if uesed.
|
||||
If you forget this data/password, you wont be able to read or write
|
||||
to the card.
|
||||
|
||||
## How do I use a password
|
||||
|
||||
This can be a little tricky for beginners.
|
||||
***If you forget your password you will lose access to your card***.
|
||||
|
||||
To tell the T5577 to use a password we have to change the data in the
|
||||
To tell the T5577 to use a password, we have to change the data in the
|
||||
configuration block (0). To help learn this and make it as simple as I
|
||||
can, please read and follow exactly. If your results DON’T match 100% as
|
||||
required, please do not proceed.
|
||||
|
|
@ -331,20 +334,20 @@ required, please do not proceed.
|
|||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 02 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 04 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 05 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 06 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 04 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 05 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 06 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 07 | 12345678 | 00010010001101000101011001111000 | .4Vx
|
||||
[+] Reading Page 1:
|
||||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
|
||||
[+] 01 | E0150A48 | 11100000000101010000101001001000 | ...H
|
||||
[+] 02 | 2D782308 | 00101101011110000010001100001000 | -x#.
|
||||
[+] 03 | FFFFFFFF | 11111111111111111111111111111111 | ....
|
||||
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
|
||||
```
|
||||
***Important : If block 0 and block 7 don’t match exactly, do not continue.***
|
||||
|
||||
|
|
@ -358,7 +361,7 @@ required, please do not proceed.
|
|||
|
||||
|
||||
We will cover other things in the configuration later. But the key
|
||||
note here is we ONLY want to change bit 28 and nothing else.
|
||||
note here, is we ONLY want to change bit 28 and nothing else.
|
||||
|
||||
Current Block 0 : ***00088040***
|
||||
New Block 0 : ***00088050***
|
||||
|
|
@ -366,7 +369,7 @@ required, please do not proceed.
|
|||
To understand what happened to get from 00088040 to 00088050 we need
|
||||
to look at the binary data.
|
||||
|
||||
While this can be confusing it is important to understand this as we
|
||||
While this can be confusing, it is important to understand this as we
|
||||
do more advanced things.
|
||||
|
||||
Bit Location (28)
|
||||
|
|
@ -380,7 +383,7 @@ required, please do not proceed.
|
|||
|
||||
|
||||
|
||||
See how in the above we change the bit in location 28 from a 0 to 1
|
||||
See how in the above we changed the bit in location 28 from a 0 to 1
|
||||
0 = No Password, 1 = Use Password
|
||||
|
||||
Note how we did NOT change any other part of the configuration, only bit 28.
|
||||
|
|
@ -415,7 +418,7 @@ required, please do not proceed.
|
|||
card.
|
||||
|
||||
Lets try again, but this time supply the password. We use the option
|
||||
p followed by the password.
|
||||
-p followed by the password.
|
||||
```
|
||||
[usb] pm3 --> lf t55 detect -p 12345678
|
||||
```
|
||||
|
|
@ -430,7 +433,7 @@ required, please do not proceed.
|
|||
[=] Block0............ 00088050 (auto detect)
|
||||
[=] Downlink mode..... default/fixed bit length
|
||||
[=] Password set...... Yes
|
||||
[=] Password.......... 00000000
|
||||
[=] Password.......... 12345678
|
||||
```
|
||||
|
||||
7) Write a block of data with a password
|
||||
|
|
@ -460,13 +463,12 @@ required, please do not proceed.
|
|||
[+] blk | hex data | binary | ascii
|
||||
[+] ----+----------+----------------------------------+-------
|
||||
[!] Safety check: Could not detect if PWD bit is set in config block. Exits.
|
||||
[?] Consider using the override parameter to force read.
|
||||
```
|
||||
|
||||
Note that the proxmark3 did not read the block, the safty kicked in
|
||||
and wants us to confirm by supply the override option ‘o’.
|
||||
and wants us to confirm by supply the override option ‘-o’.
|
||||
|
||||
Lets try again with the ‘o’ option as we know the password is set.
|
||||
Lets try again with the ‘-o’ option as we know the password is set.
|
||||
```
|
||||
[usb] pm3 --> lf t55xx read -b 1 -p 12345678 -o
|
||||
```
|
||||
|
|
@ -487,7 +489,7 @@ required, please do not proceed.
|
|||
this from above.
|
||||
|
||||
Remember if we don’t know the config and write this config to the
|
||||
card, it will over write all other settings. This can recoved the
|
||||
card, it will overwrite all other settings. This can recover the
|
||||
card, but will lose any settings you may want. So it’s a good idea
|
||||
to read the config, and set bit 28 to 0, rather than just overwrite
|
||||
the config and change the way the card works.
|
||||
|
|
@ -516,7 +518,7 @@ required, please do not proceed.
|
|||
[=] Downlink mode..... default/fixed bit length
|
||||
[=] Password set...... No
|
||||
```
|
||||
Yes we can and we can see Block 0 is the correct config 00088040
|
||||
Yes we can! We can see Block 0 is the correct config 00088040
|
||||
|
||||
# Part 2 – Configuration Blocks
|
||||
|
||||
|
|
@ -532,7 +534,7 @@ from Block 0 in Page 0. It will use this in both default read mode
|
|||
(where is sends out the blocks from 1 to x on power up), as well as when
|
||||
it responds to commands.
|
||||
|
||||
In the Read To Card, the T5577 will encode the data using the settings
|
||||
In the Reader To Card, the T5577 will encode the data using the settings
|
||||
from Block 3 Page 1. If the command is not encoded correctly it will
|
||||
ignore the command and revert back to default read mode.
|
||||
|
||||
|
|
@ -542,10 +544,10 @@ For this configuration the settings chosen will be for the purpose of
|
|||
the card when used in production. E.G. If you want the card to act like
|
||||
an EM4100, then we need to choose the settings that work like the
|
||||
EM4100; same goes for others like HID. I am not going to cover these
|
||||
here, rather use an example. Others have collect these and posted on the
|
||||
forum.
|
||||
here, rather use an example. Others have collected these and posted on the
|
||||
forum or can be found by searching the web.
|
||||
|
||||
To get started lets look back at the tech sheet.
|
||||
To get started lets look back at the data sheet.
|
||||
|
||||
|
||||
|
||||
|
|
@ -584,12 +586,11 @@ password set (if not, review and get you card back to this state).
|
|||
```
|
||||
result:
|
||||
```
|
||||
[+] Preparing to clone EM4102 to T55x7 tag with ID 0F0368568B (RF/64)
|
||||
[+] Preparing to clone EM4102 to T55x7 tag with ID 1122334455 (RF/64)
|
||||
[#] Clock rate: 64
|
||||
[#] Tag T55x7 written with 0xff83c03322a646e4
|
||||
[#] Tag T55x7 written with 0xff8c65298c94a940
|
||||
|
||||
[+] Done
|
||||
[?] Hint: try `lf em 410x reader` to verify
|
||||
```
|
||||
|
||||
2) Check this has work.
|
||||
|
|
@ -632,7 +633,7 @@ password set (if not, review and get you card back to this state).
|
|||
```
|
||||
Looks good.
|
||||
|
||||
3) Now lest see what the T5577 detect and info shows
|
||||
3) Now lets see what the T5577 detect and info shows
|
||||
```
|
||||
[usb] pm3 --> lf t55 detect
|
||||
```
|
||||
|
|
|
|||
Loading…
Reference in a new issue