//-----------------------------------------------------------------------------
// This code is licensed to you under the terms of the GNU GPL, version 2 or,
// at your option, any later version. See the LICENSE.txt file for the text of
// the license.
//-----------------------------------------------------------------------------
// Miscellaneous routines for low frequency tag operations.
// Tags supported here so far are Texas Instruments (TI), HID, EM4x05, EM410x
// Also routines for raw mode reading/simulating of LF waveform
//-----------------------------------------------------------------------------

#include "proxmark3.h"
#include "apps.h"
#include "util.h"
#include "hitag2.h"
#include "crc16.h"
#include "string.h"
#include "lfdemod.h"
#include "lfsampling.h"
#include "protocols.h"
#include "usb_cdc.h" // for usb_poll_validate_length
#include "common.h"
#include "flashmem.h" // persistence on mem

#ifndef SHORT_COIL
# define SHORT_COIL()	LOW(GPIO_SSC_DOUT)
#endif
#ifndef OPEN_COIL
# define OPEN_COIL()	HIGH(GPIO_SSC_DOUT)
#endif

//#define START_GAP 31*8 // was 250 // SPEC:  1*8 to 50*8 - typ 15*8 (15fc)
//#define WRITE_GAP 8*8 // 17*8 // was 160 // SPEC:  1*8 to 20*8 - typ 10*8 (10fc)
//#define WRITE_0   15*8 // 18*8 // was 144 // SPEC: 16*8 to 32*8 - typ 24*8 (24fc)
//#define WRITE_1   47*8 // 50*8 // was 400 // SPEC: 48*8 to 64*8 - typ 56*8 (56fc)  432 for T55x7; 448 for E5550
//#define READ_GAP  15*8

//  VALUES TAKEN FROM EM4x function: SendForward
//  START_GAP = 440;       (55*8) cycles at 125Khz (8us = 1cycle)
//  WRITE_GAP = 128;       (16*8)
//  WRITE_1   = 256 32*8;  (32*8)

//  These timings work for 4469/4269/4305 (with the 55*8 above)
//  WRITE_0 = 23*8 , 9*8

// Sam7s has several timers, we will use the source TIMER_CLOCK1 (aka AT91C_TC_CLKS_TIMER_DIV1_CLOCK)
// TIMER_CLOCK1 = MCK/2, MCK is running at 48 MHz, Timer is running at 48/2 = 24 MHz
// Hitag units (T0) have duration of 8 microseconds (us), which is 1/125000 per second (carrier)
// T0 = TIMER_CLOCK1 / 125000 = 192
// 1 Cycle = 8 microseconds(us)  == 1 field clock

// new timer:
//     = 1us = 1.5ticks
// 1fc = 8us = 12ticks
/*
Default LF T55xx config is set to:
	startgap = 31*8
	writegap = 17*8
	write_0 = 15*8
	write_1 = 47*8
	read_gap = 15*8
*/
t55xx_config t_config = { 29*8, 17*8, 15*8, 47*8, 15*8 } ;

void printT55xxConfig(void) {
	Dbprintf("LF T55XX config");
	Dbprintf("  [a] startgap............%d*8 (%d)", t_config.start_gap/8, t_config.start_gap);
	Dbprintf("  [b] writegap............%d*8 (%d)", t_config.write_gap/8, t_config.write_gap);
	Dbprintf("  [c] write_0.............%d*8 (%d)", t_config.write_0/8,   t_config.write_0);
	Dbprintf("  [d] write_1.............%d*8 (%d)", t_config.write_1/8,   t_config.write_1);
	Dbprintf("  [e] readgap.............%d*8 (%d)", t_config.read_gap/8,  t_config.read_gap);
}

void setT55xxConfig(uint8_t arg0, t55xx_config *c) {

	if (c->start_gap != 0) t_config.start_gap = c->start_gap;
	if (c->write_gap != 0) t_config.write_gap = c->write_gap;
	if (c->write_0   != 0) t_config.write_0 = c->write_0;
	if (c->write_1   != 0) t_config.write_1 = c->write_1;
	if (c->read_gap  != 0) t_config.read_gap = c->read_gap;

	printT55xxConfig();

#if WITH_FLASH
	// shall persist to flashmem
	if (arg0 == 0) {
		return;
	}
	
    if (!FlashInit()) {
        return;
	}
	
	uint8_t *buf = BigBuf_malloc(T55XX_CONFIG_LEN);
	Flash_CheckBusy(BUSY_TIMEOUT);
	uint16_t res = Flash_ReadDataCont(T55XX_CONFIG_OFFSET, buf, T55XX_CONFIG_LEN);
	if ( res == 0) {
		FlashStop();
		BigBuf_free();
		return;
	}
	
	memcpy(buf, &t_config, T55XX_CONFIG_LEN);
	
	Flash_CheckBusy(BUSY_TIMEOUT);
    Flash_WriteEnable();
	Flash_Erase4k(3, 0xD);	
	res = Flash_Write(T55XX_CONFIG_OFFSET, buf, T55XX_CONFIG_LEN);

	if ( res == T55XX_CONFIG_LEN && MF_DBGLEVEL > 1) {
		DbpString("T55XX Config save success");
	}
	
	BigBuf_free();	
#endif
}

t55xx_config* getT55xxConfig(void) {
	return &t_config;
}

void loadT55xxConfig(void) {
#if WITH_FLASH
    if (!FlashInit()) {
        return;
	}

	uint8_t *buf = BigBuf_malloc(T55XX_CONFIG_LEN);
	
	Flash_CheckBusy(BUSY_TIMEOUT);
	uint16_t isok = Flash_ReadDataCont(T55XX_CONFIG_OFFSET, buf, T55XX_CONFIG_LEN);
	FlashStop();
	
	// verify read mem is actual data.
	uint8_t cntA = T55XX_CONFIG_LEN, cntB = T55XX_CONFIG_LEN;
	for (int i=0; i< T55XX_CONFIG_LEN; i++) {
		if ( buf[i] == 0xFF) cntA--;
		if ( buf[i] == 0x00) cntB--;
	}
	if ( !cntA || !cntB ) {
		BigBuf_free();
		return;
	}
	
	memcpy((uint8_t *)&t_config, buf, T55XX_CONFIG_LEN);
	
	if ( isok == T55XX_CONFIG_LEN) {
		if (MF_DBGLEVEL > 1) DbpString("T55XX Config load success");
	}
#endif
}

/**
 * Function to do a modulation and then get samples.
 * @param delay_off
 * @param period_0
 * @param period_1
 * @param command (in binary char array)
 */
void ModThenAcquireRawAdcSamples125k(uint32_t delay_off, uint32_t period_0, uint32_t period_1, uint8_t *command) {

	// start timer
	StartTicks();

	// use lf config settings
	sample_config *sc = getSamplingConfig();

	// Make sure the tag is reset
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitMS(500);

	// clear read buffer
	BigBuf_Clear_keep_EM();

	LFSetupFPGAForADC(sc->divisor, 1);

	// little more time for the tag to fully power up
	WaitMS(200);

	// if delay_off = 0 then just bitbang 1 = antenna on 0 = off for respective periods.
	bool bitbang = delay_off == 0;
	// now modulate the reader field
	if (bitbang) {
		// HACK it appears the loop and if statements take up about 7us so adjust waits accordingly...
		uint8_t hack_cnt = 7;
		if (period_0 < hack_cnt || period_1 < hack_cnt) {
			DbpString("[!] Warning periods cannot be less than 7us in bit bang mode");
			FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
			LED_D_OFF();
			return;
		}

		// hack2 needed---  it appears to take about 8-16us to turn the antenna back on
		// leading to ~ 1 to 2 125khz samples extra in every off period
		// so we should test for last 0 before next 1 and reduce period_0 by this extra amount...
		// but is this time different for every antenna or other hw builds???  more testing needed

		// prime cmd_len to save time comparing strings while modulating
		int cmd_len = 0;
		while(command[cmd_len] != '\0' && command[cmd_len] != ' ')
			cmd_len++;

		int counter = 0;
		bool off = false;
		for (counter = 0; counter < cmd_len; counter++) {
			// if cmd = 0 then turn field off
			if (command[counter] == '0') {
				// if field already off leave alone (affects timing otherwise)
				if (off == false) {
					FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
					LED_D_OFF();
					off = true;
				}
				// note we appear to take about 7us to switch over (or run the if statements/loop...)
				WaitUS(period_0 - hack_cnt);
			// else if cmd = 1 then turn field on
			} else {
				// if field already on leave alone (affects timing otherwise)
				if (off) {
					FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
					LED_D_ON();
					off = false;
				}
				// note we appear to take about 7us to switch over (or run the if statements/loop...)
				WaitUS(period_1 - hack_cnt);
			}
		}
	} else { // old mode of cmd read using delay as off period
		while(*command != '\0' && *command != ' ') {
			LED_D_ON();
			if (*(command++) == '0')
				TurnReadLFOn(period_0);
			else
				TurnReadLFOn(period_1);

			LED_D_OFF();
			FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
			WaitUS(delay_off);
		}

		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);
	}

	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);

	// now do the read
	DoAcquisition_config(false, 0);

	// Turn off antenna
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	// tell client we are done
	cmd_send(CMD_ACK,0,0,0,0,0);
}

/* blank r/w tag data stream
...0000000000000000 01111111
1010101010101010101010101010101010101010101010101010101010101010
0011010010100001
01111111
101010101010101[0]000...

[5555fe852c5555555555555555fe0000]
*/
void ReadTItag(void)
{
	StartTicks();
	// some hardcoded initial params
	// when we read a TI tag we sample the zerocross line at 2Mhz
	// TI tags modulate a 1 as 16 cycles of 123.2Khz
	// TI tags modulate a 0 as 16 cycles of 134.2Khz
	#define FSAMPLE 2000000
	#define FREQLO 123200
	#define FREQHI 134200

	signed char *dest = (signed char *)BigBuf_get_addr();
	uint16_t n = BigBuf_max_traceLen();
	// 128 bit shift register [shift3:shift2:shift1:shift0]
	uint32_t shift3 = 0, shift2 = 0, shift1 = 0, shift0 = 0;

	int i, cycles=0, samples=0;
	// how many sample points fit in 16 cycles of each frequency
	uint32_t sampleslo = (FSAMPLE<<4)/FREQLO, sampleshi = (FSAMPLE<<4)/FREQHI;
	// when to tell if we're close enough to one freq or another
	uint32_t threshold = (sampleslo - sampleshi + 1)>>1;

	// TI tags charge at 134.2Khz
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz

	// Place FPGA in passthrough mode, in this mode the CROSS_LO line
	// connects to SSP_DIN and the SSP_DOUT logic level controls
	// whether we're modulating the antenna (high)
	// or listening to the antenna (low)
	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU);

	// get TI tag data into the buffer
	AcquireTiType();

	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);

	for (i=0; i<n-1; i++) {
		// count cycles by looking for lo to hi zero crossings
		if ( (dest[i]<0) && (dest[i+1]>0) ) {
			cycles++;
			// after 16 cycles, measure the frequency
			if (cycles>15) {
				cycles=0;
				samples=i-samples; // number of samples in these 16 cycles

				// TI bits are coming to us lsb first so shift them
				// right through our 128 bit right shift register
				shift0 = (shift0>>1) | (shift1 << 31);
				shift1 = (shift1>>1) | (shift2 << 31);
				shift2 = (shift2>>1) | (shift3 << 31);
				shift3 >>= 1;

				// check if the cycles fall close to the number
				// expected for either the low or high frequency
				if ( (samples>(sampleslo-threshold)) && (samples<(sampleslo+threshold)) ) {
					// low frequency represents a 1
					shift3 |= (1<<31);
				} else if ( (samples>(sampleshi-threshold)) && (samples<(sampleshi+threshold)) ) {
					// high frequency represents a 0
				} else {
					// probably detected a gay waveform or noise
					// use this as gaydar or discard shift register and start again
					shift3 = shift2 = shift1 = shift0 = 0;
				}
				samples = i;

				// for each bit we receive, test if we've detected a valid tag

				// if we see 17 zeroes followed by 6 ones, we might have a tag
				// remember the bits are backwards
				if ( ((shift0 & 0x7fffff) == 0x7e0000) ) {
					// if start and end bytes match, we have a tag so break out of the loop
					if ( ((shift0>>16)&0xff) == ((shift3>>8)&0xff) ) {
						cycles = 0xF0B; //use this as a flag (ugly but whatever)
						break;
					}
				}
			}
		}
	}

	// if flag is set we have a tag
	if (cycles!=0xF0B) {
		DbpString("Info: No valid tag detected.");
	} else {
		// put 64 bit data into shift1 and shift0
		shift0 = (shift0>>24) | (shift1 << 8);
		shift1 = (shift1>>24) | (shift2 << 8);

		// align 16 bit crc into lower half of shift2
		shift2 = ((shift2>>24) | (shift3 << 8)) & 0x0ffff;

		// if r/w tag, check ident match
		if (shift3 & (1<<15) ) {
			DbpString("Info: TI tag is rewriteable");
			// only 15 bits compare, last bit of ident is not valid
			if (((shift3 >> 16) ^ shift0) & 0x7fff ) {
				DbpString("Error: Ident mismatch!");
			} else {
				DbpString("Info: TI tag ident is valid");
			}
		} else {
			DbpString("Info: TI tag is readonly");
		}

		// WARNING the order of the bytes in which we calc crc below needs checking
		// i'm 99% sure the crc algorithm is correct, but it may need to eat the
		// bytes in reverse or something
		// calculate CRC
		uint32_t crc=0;

		crc = update_crc16(crc, (shift0)&0xff);
		crc = update_crc16(crc, (shift0>>8)&0xff);
		crc = update_crc16(crc, (shift0>>16)&0xff);
		crc = update_crc16(crc, (shift0>>24)&0xff);
		crc = update_crc16(crc, (shift1)&0xff);
		crc = update_crc16(crc, (shift1>>8)&0xff);
		crc = update_crc16(crc, (shift1>>16)&0xff);
		crc = update_crc16(crc, (shift1>>24)&0xff);

		Dbprintf("Info: Tag data: %x%08x, crc=%x", (unsigned int)shift1, (unsigned int)shift0, (unsigned int)shift2 & 0xFFFF);
		if (crc != (shift2&0xffff)) {
			Dbprintf("Error: CRC mismatch, expected %x", (unsigned int)crc);
		} else {
			DbpString("Info: CRC is good");
		}
	}
	StopTicks();
}

void WriteTIbyte(uint8_t b)
{
	int i = 0;

	// modulate 8 bits out to the antenna
	for (i=0; i<8; i++)
	{
		if ( b & ( 1 << i ) ) {
			// stop modulating antenna 1ms
			LOW(GPIO_SSC_DOUT);
			WaitUS(1000);
			// modulate antenna 1ms
			HIGH(GPIO_SSC_DOUT);
			WaitUS(1000);
		} else {
			// stop modulating antenna 0.3ms
			LOW(GPIO_SSC_DOUT);
			WaitUS(300);
			// modulate antenna 1.7ms
			HIGH(GPIO_SSC_DOUT);
			WaitUS(1700);
		}
	}
}

void AcquireTiType(void)
{
	int i, j, n;
	// tag transmission is <20ms, sampling at 2M gives us 40K samples max
	// each sample is 1 bit stuffed into a uint32_t so we need 1250 uint32_t
	#define TIBUFLEN 1250

	// clear buffer
	uint32_t *buf = (uint32_t *)BigBuf_get_addr();

	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_ext(false);

	// Set up the synchronous serial port
	AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DIN;
	AT91C_BASE_PIOA->PIO_ASR = GPIO_SSC_DIN;

	// steal this pin from the SSP and use it to control the modulation
	AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT;
	AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;

	AT91C_BASE_SSC->SSC_CR = AT91C_SSC_SWRST;
	AT91C_BASE_SSC->SSC_CR = AT91C_SSC_RXEN | AT91C_SSC_TXEN;

	// Sample at 2 Mbit/s, so TI tags are 16.2 vs. 14.9 clocks long
	// 48/2 = 24 MHz clock must be divided by 12
	AT91C_BASE_SSC->SSC_CMR = 12;

	AT91C_BASE_SSC->SSC_RCMR = SSC_CLOCK_MODE_SELECT(0);
	AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(32) | AT91C_SSC_MSBF;
	// Transmit Clock Mode Register
	AT91C_BASE_SSC->SSC_TCMR = 0;
	// Transmit Frame Mode Register
	AT91C_BASE_SSC->SSC_TFMR = 0;
	// iceman, FpgaSetupSsc() ?? the code above? can it be replaced?
	LED_D_ON();

	// modulate antenna
	HIGH(GPIO_SSC_DOUT);

	// Charge TI tag for 50ms.
	WaitMS(50);

	// stop modulating antenna and listen
	LOW(GPIO_SSC_DOUT);

	LED_D_OFF();

	i = 0;
	for (;;) {
		if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) {
			buf[i] = AT91C_BASE_SSC->SSC_RHR;	// store 32 bit values in buffer
			i++;
			if (i >= TIBUFLEN) break;
		}
		WDT_HIT();
	}

	// return stolen pin to SSP
	AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT;
	AT91C_BASE_PIOA->PIO_ASR = GPIO_SSC_DIN | GPIO_SSC_DOUT;

	char *dest = (char *)BigBuf_get_addr();
	n = TIBUFLEN * 32;

	// unpack buffer
	for (i = TIBUFLEN-1; i >= 0; i--) {
		for (j = 0; j < 32; j++) {
			if(buf[i] & (1 << j)) {
				dest[--n] = 1;
			} else {
				dest[--n] = -1;
			}
		}
	}

	// reset SSC
	FpgaSetupSsc();
}

// arguments: 64bit data split into 32bit idhi:idlo and optional 16bit crc
// if crc provided, it will be written with the data verbatim (even if bogus)
// if not provided a valid crc will be computed from the data and written.
void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc)
{
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	if(crc == 0) {
		crc = update_crc16(crc, (idlo)&0xff);
		crc = update_crc16(crc, (idlo>>8)&0xff);
		crc = update_crc16(crc, (idlo>>16)&0xff);
		crc = update_crc16(crc, (idlo>>24)&0xff);
		crc = update_crc16(crc, (idhi)&0xff);
		crc = update_crc16(crc, (idhi>>8)&0xff);
		crc = update_crc16(crc, (idhi>>16)&0xff);
		crc = update_crc16(crc, (idhi>>24)&0xff);
	}
	Dbprintf("Writing to tag: %x%08x, crc=%x",	idhi, idlo, crc);

	// TI tags charge at 134.2Khz
	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
	// Place FPGA in passthrough mode, in this mode the CROSS_LO line
	// connects to SSP_DIN and the SSP_DOUT logic level controls
	// whether we're modulating the antenna (high)
	// or listening to the antenna (low)
	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU);
	StartTicks();

	LED_A_ON();

	// steal this pin from the SSP and use it to control the modulation
	AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT;
	AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;

	// writing algorithm:
	// a high bit consists of a field off for 1ms and field on for 1ms
	// a low bit consists of a field off for 0.3ms and field on for 1.7ms
	// initiate a charge time of 50ms (field on) then immediately start writing bits
	// start by writing 0xBB (keyword) and 0xEB (password)
	// then write 80 bits of data (or 64 bit data + 16 bit crc if you prefer)
	// finally end with 0x0300 (write frame)
	// all data is sent lsb first
	// finish with 50ms programming time

	// modulate antenna
	HIGH(GPIO_SSC_DOUT);
	WaitMS(50);	// charge time

	WriteTIbyte(0xbb); // keyword
	WriteTIbyte(0xeb); // password
	WriteTIbyte( (idlo    )&0xff );
	WriteTIbyte( (idlo>>8 )&0xff );
	WriteTIbyte( (idlo>>16)&0xff );
	WriteTIbyte( (idlo>>24)&0xff );
	WriteTIbyte( (idhi    )&0xff );
	WriteTIbyte( (idhi>>8 )&0xff );
	WriteTIbyte( (idhi>>16)&0xff );
	WriteTIbyte( (idhi>>24)&0xff ); // data hi to lo
	WriteTIbyte( (crc     )&0xff ); // crc lo
	WriteTIbyte( (crc>>8  )&0xff ); // crc hi
	WriteTIbyte(0x00); // write frame lo
	WriteTIbyte(0x03); // write frame hi
	HIGH(GPIO_SSC_DOUT);
	WaitMS(50);	// programming time

	LED_A_OFF();

	// get TI tag data into the buffer
	AcquireTiType();

	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	DbpString("Now use `lf ti read` to check");
	StopTicks();
}

// note:   a call to FpgaDownloadAndGo(FPGA_BITSTREAM_LF) must be done before, but
//  this may destroy the bigbuf so be sure this is called before calling SimulateTagLowFrequencyEx
void SimulateTagLowFrequencyEx(int period, int gap, int ledcontrol, int numcycles) {

	//FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_TOGGLE_MODE );
	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT);
	SpinDelay(20);

	int i = 0, x = 0;
	uint8_t *buf = BigBuf_get_addr();

	// set frequency,  get values from 'lf config' command
	sample_config *sc = getSamplingConfig();

	if ( (sc->divisor == 1) || (sc->divisor < 0) || (sc->divisor > 255) )
		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
	else if (sc->divisor == 0)
		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
	else
		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);

	AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT | GPIO_SSC_CLK;
	AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;
	AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_CLK;

	for(;;) {

		if ( numcycles > -1 ) {
			if ( x != numcycles ) {
				++x;
			} else {
				// exit without turning of field
				return;
			}
		}

		if (ledcontrol) LED_D_ON();

		// wait until SSC_CLK goes HIGH
		// used as a simple detection of a reader field?
		while (!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)) {
			WDT_HIT();
			if ( usb_poll_validate_length() || BUTTON_PRESS() )
				goto OUT;
		}

		if(buf[i])
			OPEN_COIL();
		else
			SHORT_COIL();

		//wait until SSC_CLK goes LOW
		while (AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK) {
			WDT_HIT();
			//if ( usb_poll_validate_length() || BUTTON_PRESS() )
			if ( BUTTON_PRESS() )
				goto OUT;
		}

		i++;
		if(i == period) {
			i = 0;
			if (gap) {
				SHORT_COIL();
				SpinDelayUs(gap);
			}
		}

		if (ledcontrol) LED_D_OFF();
	}
OUT:
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	LED_D_OFF();
}

void SimulateTagLowFrequency(int period, int gap, int ledcontrol) {
	SimulateTagLowFrequencyEx(period, gap, ledcontrol, -1);
}


#define DEBUG_FRAME_CONTENTS 1
void SimulateTagLowFrequencyBidir(int divisor, int t0)
{
}
// compose fc/5 fc/8  waveform (FSK1)

// compose fc/8 fc/10 waveform (FSK2)
// also manchester,
static void fc(int c, int *n)
{
	uint8_t *dest = BigBuf_get_addr();
	int idx;

	// for when we want an fc8 pattern every 4 logical bits
	if(c==0) {
		dest[((*n)++)]=1;
		dest[((*n)++)]=1;
		dest[((*n)++)]=1;
		dest[((*n)++)]=1;
		dest[((*n)++)]=0;
		dest[((*n)++)]=0;
		dest[((*n)++)]=0;
		dest[((*n)++)]=0;
	}

	//	an fc/8  encoded bit is a bit pattern of  11110000  x6 = 48 samples
	if(c==8) {
		for (idx=0; idx<6; idx++) {
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
		}
	}

	//	an fc/10 encoded bit is a bit pattern of 1111100000 x5 = 50 samples
	if(c==10) {
		for (idx=0; idx<5; idx++) {
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=1;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
			dest[((*n)++)]=0;
		}
	}
}

// special start of frame marker containing invalid bit sequences
// this one is focused on HID,  with manchester encoding.
static void fcSTT(int *n) {
	fc(8,  n);	fc(8,  n); // invalid
	fc(8,  n);	fc(10, n); // logical 0
	fc(10, n);	fc(10, n); // invalid
	fc(8,  n);	fc(10, n); // logical 0
}

// compose fc/X fc/Y waveform (FSKx)
static void fcAll(uint8_t fc, int *n, uint8_t clock, uint16_t *modCnt)
{
	uint8_t *dest = BigBuf_get_addr();
	uint8_t halfFC = fc/2;
	uint8_t wavesPerClock = clock/fc;
	uint8_t mod = clock % fc;    //modifier
	uint8_t modAdj = fc/mod;     //how often to apply modifier
	bool modAdjOk = !(fc % mod); //if (fc % mod==0) modAdjOk = true;

	// loop through clock - step field clock
	for (uint8_t idx=0; idx < wavesPerClock; idx++){
		// put 1/2 FC length 1's and 1/2 0's per field clock wave (to create the wave)
		memset(dest+(*n), 0, fc-halfFC);  //in case of odd number use extra here
		memset(dest+(*n)+(fc-halfFC), 1, halfFC);
		*n += fc;
	}
	if (mod>0) (*modCnt)++;
	if ((mod>0) && modAdjOk){  //fsk2
		if ((*modCnt % modAdj) == 0){ //if 4th 8 length wave in a rf/50 add extra 8 length wave
			memset(dest+(*n), 0, fc-halfFC);
			memset(dest+(*n)+(fc-halfFC), 1, halfFC);
			*n += fc;
		}
	}
	if (mod>0 && !modAdjOk){  //fsk1
		memset(dest+(*n), 0, mod-(mod/2));
		memset(dest+(*n)+(mod-(mod/2)), 1, mod/2);
		*n += mod;
	}
}

// prepare a waveform pattern in the buffer based on the ID given then
// simulate a HID tag until the button is pressed
void CmdHIDsimTAGEx( uint32_t hi, uint32_t lo, int ledcontrol, int numcycles) {

	if (hi > 0xFFF) {
		DbpString("[!] tags can only have 44 bits. - USE lf simfsk for larger tags");
		return;
	}

	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	set_tracing(false);

	int n = 0, i = 0;
	/*
	 HID tag bitstream format
	 The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits
	 A 1 bit is represented as 6 fc8 and 5 fc10 patterns  (manchester 10) during 2 clock periods. (1bit = 1clock period)
	 A 0 bit is represented as 5 fc10 and 6 fc8 patterns  (manchester 01)
	 A fc8 is inserted before every 4 bits
	 A special start of frame pattern is used consisting a0b0 where a and b are neither 0
	 nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10)

	 FSK2a
	 bit 1 = fc10
	 bit 0 = fc8
	*/

	fc(0, &n);

	// special start of frame marker containing invalid bit sequences
	fcSTT(&n);

	// manchester encode bits 43 to 32
	for (i=11; i>=0; i--) {

		if ((i%4)==3) fc(0, &n);

		if ((hi>>i) & 1) {
			fc(10, &n); fc(8,  &n);		// low-high transition
		} else {
			fc(8,  &n); fc(10, &n);		// high-low transition
		}
	}

	// manchester encode bits 31 to 0
	for (i=31; i>=0; i--) {

		if ((i%4)==3) fc(0, &n);

		if ((lo>>i) & 1) {
			fc(10, &n); fc(8,  &n);		// low-high transition
		} else {
			fc(8,  &n); fc(10, &n);		// high-low transition
		}
	}

	if (ledcontrol)	LED_A_ON();
	SimulateTagLowFrequencyEx(n, 0, ledcontrol, numcycles);
	if (ledcontrol)	LED_A_OFF();
}

void CmdHIDsimTAG( uint32_t hi, uint32_t lo, int ledcontrol) {
	CmdHIDsimTAGEx( hi, lo, ledcontrol, -1);
	DbpString("[!] simulation finished");
}

// prepare a waveform pattern in the buffer based on the ID given then
// simulate a FSK tag until the button is pressed
// arg1 contains fcHigh and fcLow, arg2 contains STT marker and clock
void CmdFSKsimTAG(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *bits) {
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);

	// free eventually allocated BigBuf memory
	BigBuf_free(); BigBuf_Clear_ext(false);
	clear_trace();
	set_tracing(false);

	int ledcontrol = 1, n = 0, i = 0;
	uint8_t fcHigh = arg1 >> 8;
	uint8_t fcLow = arg1 & 0xFF;
	uint16_t modCnt = 0;
	uint8_t clk = arg2 & 0xFF;
	uint8_t stt = (arg2 >> 8) & 1;

	if ( stt ) {
		//int fsktype = ( fcHigh == 8 && fcLow == 5) ? 1 : 2;
		//fcSTT(&n);
	}

	for (i=0; i<size; i++){
		if (bits[i])
			fcAll(fcLow, &n, clk, &modCnt);
		else
			fcAll(fcHigh, &n, clk, &modCnt);
	}

	WDT_HIT();

	Dbprintf("Simulating with fcHigh: %d, fcLow: %d, clk: %d, STT: %d, n: %d", fcHigh, fcLow, clk, stt, n);

	if (ledcontrol)	LED_A_ON();
	SimulateTagLowFrequency(n, 0, ledcontrol);
	if (ledcontrol)	LED_A_OFF();
}

// compose ask waveform for one bit(ASK)
static void askSimBit(uint8_t c, int *n, uint8_t clock, uint8_t manchester)
{
	uint8_t *dest = BigBuf_get_addr();
	uint8_t halfClk = clock/2;
	// c = current bit 1 or 0
	if (manchester==1){
		memset(dest+(*n), c, halfClk);
		memset(dest+(*n) + halfClk, c^1, halfClk);
	} else {
		memset(dest+(*n), c, clock);
	}
	*n += clock;
}

static void biphaseSimBit(uint8_t c, int *n, uint8_t clock, uint8_t *phase)
{
	uint8_t *dest = BigBuf_get_addr();
	uint8_t halfClk = clock/2;
	if (c){
		memset(dest+(*n), c ^ 1 ^ *phase, halfClk);
		memset(dest+(*n) + halfClk, c ^ *phase, halfClk);
	} else {
		memset(dest+(*n), c ^ *phase, clock);
		*phase ^= 1;
	}
	*n += clock;
}

static void stAskSimBit(int *n, uint8_t clock) {
	uint8_t *dest = BigBuf_get_addr();
	uint8_t halfClk = clock/2;
	//ST = .5 high .5 low 1.5 high .5 low 1 high
	memset(dest+(*n), 1, halfClk);
	memset(dest+(*n) + halfClk, 0, halfClk);
	memset(dest+(*n) + clock, 1, clock + halfClk);
	memset(dest+(*n) + clock*2 + halfClk, 0, halfClk);
	memset(dest+(*n) + clock*3, 1, clock);
	*n += clock*4;
}

// args clock, ask/man or askraw, invert, transmission separator
void CmdASKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
{
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	set_tracing(false);

	int ledcontrol = 1, n = 0, i = 0;
	uint8_t clk = (arg1 >> 8) & 0xFF;
	uint8_t encoding = arg1 & 0xFF;
	uint8_t separator = arg2 & 1;
	uint8_t invert = (arg2 >> 8) & 1;

	if (encoding == 2){  //biphase
		uint8_t phase = 0;
		for (i=0; i<size; i++){
			biphaseSimBit(BitStream[i]^invert, &n, clk, &phase);
		}
		if (phase == 1) { //run a second set inverted to keep phase in check
			for (i=0; i<size; i++){
				biphaseSimBit(BitStream[i]^invert, &n, clk, &phase);
			}
		}
	} else {  // ask/manchester || ask/raw
		for (i=0; i<size; i++){
			askSimBit(BitStream[i]^invert, &n, clk, encoding);
		}
		if (encoding==0 && BitStream[0]==BitStream[size-1]){ //run a second set inverted (for ask/raw || biphase phase)
			for (i=0; i<size; i++){
				askSimBit(BitStream[i]^invert^1, &n, clk, encoding);
			}
		}
	}
	if (separator==1 && encoding == 1)
		stAskSimBit(&n, clk);
	else if (separator==1)
		Dbprintf("sorry but separator option not yet available");

	WDT_HIT();

	Dbprintf("Simulating with clk: %d, invert: %d, encoding: %d, separator: %d, n: %d",clk, invert, encoding, separator, n);

	if (ledcontrol)	LED_A_ON();
	SimulateTagLowFrequency(n, 0, ledcontrol);
	if (ledcontrol)	LED_A_OFF();
}

//carrier can be 2,4 or 8
static void pskSimBit(uint8_t waveLen, int *n, uint8_t clk, uint8_t *curPhase, bool phaseChg)
{
	uint8_t *dest = BigBuf_get_addr();
	uint8_t halfWave = waveLen/2;
	//uint8_t idx;
	int i = 0;
	if (phaseChg){
		// write phase change
		memset(dest+(*n), *curPhase^1, halfWave);
		memset(dest+(*n) + halfWave, *curPhase, halfWave);
		*n += waveLen;
		*curPhase ^= 1;
		i += waveLen;
	}
	//write each normal clock wave for the clock duration
	for (; i < clk; i+=waveLen){
		memset(dest+(*n), *curPhase, halfWave);
		memset(dest+(*n) + halfWave, *curPhase^1, halfWave);
		*n += waveLen;
	}
}

// args clock, carrier, invert,
void CmdPSKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
{
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
	set_tracing(false);

	int ledcontrol = 1, n = 0, i = 0;
	uint8_t clk = arg1 >> 8;
	uint8_t carrier = arg1 & 0xFF;
	uint8_t invert = arg2 & 0xFF;
	uint8_t curPhase = 0;
	for (i=0; i<size; i++){
		if (BitStream[i] == curPhase){
			pskSimBit(carrier, &n, clk, &curPhase, false);
		} else {
			pskSimBit(carrier, &n, clk, &curPhase, true);
		}
	}

	WDT_HIT();

	Dbprintf("Simulating with Carrier: %d, clk: %d, invert: %d, n: %d",carrier, clk, invert, n);

	if (ledcontrol)	LED_A_ON();
	SimulateTagLowFrequency(n, 0, ledcontrol);
	if (ledcontrol)	LED_A_OFF();
}

// loop to get raw HID waveform then FSK demodulate the TAG ID from it
void CmdHIDdemodFSK(int findone, uint32_t *high, uint32_t *low, int ledcontrol) {
	uint8_t *dest = BigBuf_get_addr();
	size_t size = 0;
	uint32_t hi2 = 0, hi = 0, lo = 0;
	int idx = 0;
	int dummyIdx = 0;
	// Configure to go in 125Khz listen mode
	LFSetupFPGAForADC(95, true);

	//clear read buffer
	BigBuf_Clear_keep_EM();

	while( !BUTTON_PRESS() && !usb_poll_validate_length()) {

		WDT_HIT();
		if (ledcontrol) LED_A_ON();

		DoAcquisition_default(-1, true);
		// FSK demodulator
		size = 50*128*2; //big enough to catch 2 sequences of largest format
		idx = HIDdemodFSK(dest, &size, &hi2, &hi, &lo, &dummyIdx);
		if ( idx < 0 ) continue;

		if (idx > 0 && lo > 0 && (size == 96 || size == 192)){
			// go over previously decoded manchester data and decode into usable tag ID
			if (hi2 != 0){ //extra large HID tags  88/192 bits
				Dbprintf("TAG ID: %x%08x%08x (%d)",
					hi2,
					hi,
					lo,
					(lo >> 1) & 0xFFFF
				);
			} else {  //standard HID tags 44/96 bits
				uint8_t bitlen = 0;
				uint32_t fc = 0;
				uint32_t cardnum = 0;

				if (((hi >> 5) & 1) == 1){//if bit 38 is set then < 37 bit format is used
					uint32_t lo2 = 0;
					lo2=(((hi & 31) << 12) | (lo>>20)); //get bits 21-37 to check for format len bit
					uint8_t idx3 = 1;
					while (lo2 > 1){ //find last bit set to 1 (format len bit)
						lo2 >>= 1;
						idx3++;
					}
					bitlen = idx3 + 19;
					fc = 0;
					cardnum = 0;
					if (bitlen == 26){
						cardnum = (lo >> 1) & 0xFFFF;
						fc = (lo >> 17) & 0xFF;
					}
					if (bitlen == 37){
						cardnum = (lo >> 1 ) & 0x7FFFF;
						fc = ((hi & 0xF) << 12) | (lo >> 20);
					}
					if (bitlen == 34){
						cardnum = (lo >> 1) & 0xFFFF;
						fc = ((hi & 1) << 15) | (lo >> 17);
					}
					if (bitlen == 35){
						cardnum = (lo >> 1) & 0xFFFFF;
						fc = ((hi & 1) << 11)|(lo >> 21);
					}
				}
				else { //if bit 38 is not set then 37 bit format is used
					bitlen= 37;
					fc = 0;
					cardnum = 0;
					if (bitlen == 37){
						cardnum = (lo >> 1) & 0x7FFFF;
						fc = ((hi & 0xF) << 12) | (lo >> 20);
					}
				}
				Dbprintf("TAG ID: %x%08x (%d) - Format Len: %dbit - FC: %d - Card: %d",
						 hi,
						 lo,
						 (lo >> 1) & 0xFFFF,
						 bitlen,
						 fc,
						 cardnum
					);
			}
			if (findone){
				*high = hi;
				*low = lo;
				break;
			}
			// reset
		}
		hi2 = hi = lo = idx = 0;
	}
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	DbpString("Stopped");
	if (ledcontrol) LED_A_OFF();
}

// loop to get raw HID waveform then FSK demodulate the TAG ID from it
void CmdAWIDdemodFSK(int findone, uint32_t *high, uint32_t *low, int ledcontrol) {

	uint8_t *dest = BigBuf_get_addr();

	//big enough to catch 2 sequences of largest format
	size_t size = 12800; //50 * 128 * 2;

	int idx = 0, dummyIdx = 0;

	BigBuf_Clear_keep_EM();

	LFSetupFPGAForADC(95, true);

	while (!BUTTON_PRESS() && !usb_poll_validate_length()) {

		WDT_HIT();
		if (ledcontrol) LED_A_ON();

		DoAcquisition_default(-1, true);
		// FSK demodulator

		idx = detectAWID(dest, &size, &dummyIdx);

		if (idx <= 0 || size != 96) continue;
		// Index map
		// 0            10            20            30              40            50              60
		// |            |             |             |               |             |               |
		// 01234567 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 - to 96
		// -----------------------------------------------------------------------------
		// 00000001 000 1 110 1 101 1 011 1 101 1 010 0 000 1 000 1 010 0 001 0 110 1 100 0 000 1 000 1
		// premable bbb o bbb o bbw o fff o fff o ffc o ccc o ccc o ccc o ccc o ccc o wxx o xxx o xxx o - to 96
		//          |---26 bit---|    |-----117----||-------------142-------------|
		// b = format bit len, o = odd parity of last 3 bits
		// f = facility code, c = card number
		// w = wiegand parity
		// (26 bit format shown)

		//get raw ID before removing parities
		uint32_t rawLo = bytebits_to_byte(dest+idx+64, 32);
		uint32_t rawHi = bytebits_to_byte(dest+idx+32, 32);
		uint32_t rawHi2 = bytebits_to_byte(dest+idx, 32);

		size = removeParity(dest, idx+8, 4, 1, 88);
		if (size != 66) continue;
		// ok valid card found!

		// Index map
		// 0           10         20        30          40        50        60
		// |           |          |         |           |         |         |
		// 01234567 8 90123456 7890123456789012 3 456789012345678901234567890123456
		// -----------------------------------------------------------------------------
		// 00011010 1 01110101 0000000010001110 1 000000000000000000000000000000000
		// bbbbbbbb w ffffffff cccccccccccccccc w xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
		// |26 bit|   |-117--| |-----142------|
		// b = format bit len, o = odd parity of last 3 bits
		// f = facility code, c = card number
		// w = wiegand parity
		// (26 bit format shown)

		uint32_t fc = 0;
		uint32_t cardnum = 0;
		uint32_t code1 = 0;
		uint32_t code2 = 0;
		uint8_t fmtLen = bytebits_to_byte(dest, 8);
		if (fmtLen == 26){
			fc = bytebits_to_byte(dest+9, 8);
			cardnum = bytebits_to_byte(dest+17, 16);
			code1 = bytebits_to_byte(dest+8, fmtLen);
			Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %d - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, rawHi2, rawHi, rawLo);
		} else {
			cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16);
			if (fmtLen > 32){
				code1 = bytebits_to_byte(dest+8, fmtLen-32);
				code2 = bytebits_to_byte(dest+8+(fmtLen-32), 32);
				Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, code2, rawHi2, rawHi, rawLo);
			} else{
				code1 = bytebits_to_byte(dest+8, fmtLen);
				Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, rawHi2, rawHi, rawLo);
			}
		}
		if (findone){
			if (ledcontrol)	LED_A_OFF();
			*high = rawHi;
			*low = rawLo;
			break;
		}
		// reset
		idx = 0;
		WDT_HIT();
	}
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	DbpString("Stopped");
	if (ledcontrol) LED_A_OFF();
}

void CmdEM410xdemod(int findone, uint32_t *high, uint64_t *low, int ledcontrol) {
	uint8_t *dest = BigBuf_get_addr();

	size_t size = 0, idx = 0;
	int clk = 0, invert = 0, errCnt = 0, maxErr = 20;
	uint32_t hi = 0;
	uint64_t lo = 0;

	BigBuf_Clear_keep_EM();

	LFSetupFPGAForADC(95, true);

	while(!BUTTON_PRESS() && !usb_poll_validate_length()) {

		WDT_HIT();
		if (ledcontrol) LED_A_ON();

		DoAcquisition_default(-1, true);

		size  = BigBuf_max_traceLen();
		//askdemod and manchester decode
		if (size > 16385) size = 16385; //big enough to catch 2 sequences of largest format
		errCnt = askdemod(dest, &size, &clk, &invert, maxErr, 0, 1);
		WDT_HIT();

		if (errCnt < 0) continue;

			errCnt = Em410xDecode(dest, &size, &idx, &hi, &lo);
			if (errCnt == 1){
				if (size == 128){
					Dbprintf("EM XL TAG ID: %06x%08x%08x - (%05d_%03d_%08d)",
					  hi,
					  (uint32_t)(lo >> 32),
					  (uint32_t)lo,
					  (uint32_t)(lo & 0xFFFF),
					  (uint32_t)((lo >> 16LL) & 0xFF),
					  (uint32_t)(lo & 0xFFFFFF));
				} else {
					Dbprintf("EM TAG ID: %02x%08x - (%05d_%03d_%08d)",
					  (uint32_t)(lo >> 32),
					  (uint32_t)lo,
					  (uint32_t)(lo & 0xFFFF),
					  (uint32_t)((lo >> 16LL) & 0xFF),
					  (uint32_t)(lo & 0xFFFFFF));
				}

			if (findone){
				if (ledcontrol) LED_A_OFF();
				*high = hi;
				*low = lo;
				break;
			}
		}
		WDT_HIT();
		hi = lo = size = idx = 0;
		clk = invert = errCnt = 0;
	}
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	DbpString("Stopped");
	if (ledcontrol) LED_A_OFF();
}

void CmdIOdemodFSK(int findone, uint32_t *high, uint32_t *low, int ledcontrol) {

	uint8_t *dest = BigBuf_get_addr();

	int dummyIdx = 0, idx = 0;
	uint32_t code = 0, code2 = 0;
	uint8_t version = 0, facilitycode = 0, crc = 0;
	uint16_t number = 0, calccrc = 0;

	size_t size = BigBuf_max_traceLen();

	BigBuf_Clear_keep_EM();

	// Configure to go in 125Khz listen mode
	LFSetupFPGAForADC(95, true);

	while (!BUTTON_PRESS() && !usb_poll_validate_length()) {
		WDT_HIT();
		if (ledcontrol) LED_A_ON();

		DoAcquisition_default(-1, true);

		//fskdemod and get start index
		WDT_HIT();
		idx = detectIOProx(dest, &size, &dummyIdx);
		if (idx < 0) continue;
			//valid tag found

			//Index map
			//0           10          20          30          40          50          60
			//|           |           |           |           |           |           |
			//01234567 8 90123456 7 89012345 6 78901234 5 67890123 4 56789012 3 45678901 23
			//-----------------------------------------------------------------------------
            //00000000 0 11110000 1 facility 1 version* 1 code*one 1 code*two 1 checksum 11
			//
			//Checksum:
			//00000000 0 11110000 1 11100000 1 00000001 1 00000011 1 10110110 1 01110101 11
			//preamble      F0         E0         01         03         B6         75
			// How to calc checksum,
			// http://www.proxmark.org/forum/viewtopic.php?id=364&p=6
			//   F0 + E0 + 01 + 03 + B6 = 28A
			//   28A & FF = 8A
			//   FF - 8A = 75
			// Checksum: 0x75
			//XSF(version)facility:codeone+codetwo
			//Handle the data
			// if(findone){ //only print binary if we are doing one
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx],   dest[idx+1],   dest[idx+2],dest[idx+3],dest[idx+4],dest[idx+5],dest[idx+6],dest[idx+7],dest[idx+8]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+9], dest[idx+10],dest[idx+11],dest[idx+12],dest[idx+13],dest[idx+14],dest[idx+15],dest[idx+16],dest[idx+17]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+18],dest[idx+19],dest[idx+20],dest[idx+21],dest[idx+22],dest[idx+23],dest[idx+24],dest[idx+25],dest[idx+26]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+27],dest[idx+28],dest[idx+29],dest[idx+30],dest[idx+31],dest[idx+32],dest[idx+33],dest[idx+34],dest[idx+35]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+36],dest[idx+37],dest[idx+38],dest[idx+39],dest[idx+40],dest[idx+41],dest[idx+42],dest[idx+43],dest[idx+44]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+45],dest[idx+46],dest[idx+47],dest[idx+48],dest[idx+49],dest[idx+50],dest[idx+51],dest[idx+52],dest[idx+53]);
				// Dbprintf("%d%d%d%d%d%d%d%d %d%d",dest[idx+54],dest[idx+55],dest[idx+56],dest[idx+57],dest[idx+58],dest[idx+59],dest[idx+60],dest[idx+61],dest[idx+62],dest[idx+63]);
			// }
			code = bytebits_to_byte(dest+idx, 32);
			code2 = bytebits_to_byte(dest+idx+32, 32);
			version = bytebits_to_byte(dest+idx+27, 8); //14,4
			facilitycode = bytebits_to_byte(dest+idx+18, 8);
			number = (bytebits_to_byte(dest+idx+36, 8) << 8) | (bytebits_to_byte(dest+idx+45, 8)); //36,9

			crc = bytebits_to_byte(dest+idx+54, 8);
			for (uint8_t i=1; i<6; ++i)
				calccrc += bytebits_to_byte(dest+idx+9*i, 8);
			calccrc &= 0xff;
			calccrc = 0xff - calccrc;

			char *crcStr = (crc == calccrc) ? "ok" : "!crc";

            Dbprintf("IO Prox XSF(%02d)%02x:%05d (%08x%08x)  [%02x %s]", version, facilitycode, number, code, code2, crc, crcStr);
			// if we're only looking for one tag
			if (findone){
				if (ledcontrol)	LED_A_OFF();
				*high = code;
				*low = code2;
				break;
			}
			code = code2 = 0;
			version = facilitycode = 0;
			number = 0;
			idx = 0;

		WDT_HIT();
	}
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	DbpString("Stopped");
	if (ledcontrol) LED_A_OFF();
}

/*------------------------------
 * T5555/T5557/T5567/T5577 routines
 *------------------------------
 * NOTE: T55x7/T5555 configuration register definitions moved to protocols.h
 *
 * Relevant communication times in microsecond
 * To compensate antenna falling times shorten the write times
 * and enlarge the gap ones.
 * Q5 tags seems to have issues when these values changes.
 */

void TurnReadLFOn(uint32_t delay) {
	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);

	// measure antenna strength.
	//int adcval = ((MAX_ADC_LF_VOLTAGE * AvgAdc(ADC_CHAN_LF)) >> 10);
	WaitUS(delay);
}
void TurnReadLF_off(uint32_t delay) {
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(delay);
}

// Write one bit to card
void T55xxWriteBit(int bit) {
	if (!bit)
		TurnReadLFOn(t_config.write_0);
	else
		TurnReadLFOn(t_config.write_1);
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(t_config.write_gap);
}

// Send T5577 reset command then read stream (see if we can identify the start of the stream)
void T55xxResetRead(void) {
	LED_A_ON();
	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_keep_EM();

	StartTicks();

	// Set up FPGA, 125kHz
	LFSetupFPGAForADC(95, true);
	// make sure tag is fully powered up...
	WaitMS(4);

	// Trigger T55x7 in mode.
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(t_config.start_gap);

	// reset tag - op code 00
	T55xxWriteBit(0);
	T55xxWriteBit(0);

	TurnReadLFOn(t_config.read_gap);

	// Acquisition
	DoPartialAcquisition(0, true, BigBuf_max_traceLen(), 0);

	// Turn the field off
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
	cmd_send(CMD_ACK,0,0,0,0,0);
	LED_A_OFF();
}

// Write one card block in page 0, no lock
void T55xxWriteBlockExt(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) {
	LED_A_ON();
	bool PwdMode = arg & 0x1;
	uint8_t Page = (arg & 0x2)>>1;
	bool testMode = arg & 0x4;
	uint32_t i = 0;

	StartTicks();

	// Set up FPGA, 125kHz
	LFSetupFPGAForADC(95, true);

	// make sure tag is fully powered up...
	WaitMS(4);
	// Trigger T55x7 in mode.
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(t_config.start_gap);

	if (testMode) Dbprintf("TestMODE");
	// Std Opcode 10
	T55xxWriteBit(testMode ? 0 : 1);
	T55xxWriteBit(testMode ? 1 : Page); //Page 0

	if (PwdMode){
		// Send Pwd
		for (i = 0x80000000; i != 0; i >>= 1)
			T55xxWriteBit(Pwd & i);
	}
	// Send Lock bit
	T55xxWriteBit(0);

	// Send Data
	for (i = 0x80000000; i != 0; i >>= 1)
		T55xxWriteBit(Data & i);

	// Send Block number
	for (i = 0x04; i != 0; i >>= 1)
		T55xxWriteBit(Block & i);

	// Perform write (nominal is 5.6 ms for T55x7 and 18ms for E5550,
	// so wait a little more)

	// "there is a clock delay before programming"
	//  - programming takes ~5.6ms for t5577 ~18ms for E5550 or t5567
	//  so we should wait 1 clock + 5.6ms then read response?
	//  but we need to know we are dealing with t5577 vs t5567 vs e5550 (or q5) marshmellow...
	if (testMode) {
		//TESTMODE TIMING TESTS:
		// <566us does nothing
		// 566-568 switches between wiping to 0s and doing nothing
		// 5184 wipes and allows 1 block to be programmed.
		// indefinite power on wipes and then programs all blocks with bitshifted data sent.
		TurnReadLFOn(5184);

	} else {
		TurnReadLFOn(20 * 1000);

		//could attempt to do a read to confirm write took
		// as the tag should repeat back the new block
		// until it is reset, but to confirm it we would
		// need to know the current block 0 config mode for
		// modulation clock an other details to demod the response...
		// response should be (for t55x7) a 0 bit then (ST if on)
		// block data written in on repeat until reset.

		//DoPartialAcquisition(20, true, 12000);
	}

	// turn field off
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	LED_A_OFF();
}

// Write one card block in page 0, no lock
void T55xxWriteBlock(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) {
	T55xxWriteBlockExt(Data, Block, Pwd, arg);
	cmd_send(CMD_ACK,0,0,0,0,0);
}

// Read one card block in page [page]
void T55xxReadBlock(uint16_t arg0, uint8_t Block, uint32_t Pwd) {
	LED_A_ON();
	bool PwdMode = arg0 & 0x1;
	uint8_t Page = (arg0 & 0x2) >> 1;
	uint32_t i = 0;
	bool RegReadMode = (Block == 0xFF);//regular read mode

	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_keep_EM();

	//make sure block is at max 7
	Block &= 0x7;

	StartTicks();

	// Set up FPGA, 125kHz to power up the tag
	LFSetupFPGAForADC(95, true);
	// make sure tag is fully powered up...
	WaitMS(4);
	// Trigger T55x7 Direct Access Mode with start gap
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(t_config.start_gap);

	// Opcode 1[page]
	T55xxWriteBit(1);
	T55xxWriteBit(Page); //Page 0

	if (PwdMode){
		// Send Pwd
		for (i = 0x80000000; i != 0; i >>= 1)
			T55xxWriteBit(Pwd & i);
	}
	// Send a zero bit separation
	T55xxWriteBit(0);

	// Send Block number (if direct access mode)
	if (!RegReadMode)
		for (i = 0x04; i != 0; i >>= 1)
			T55xxWriteBit(Block & i);

	// Turn field on to read the response
	// 137*8 seems to get to the start of data pretty well...
	//  but we want to go past the start and let the repeating data settle in...
	TurnReadLFOn(210*8);

	// Acquisition
	// Now do the acquisition
	DoPartialAcquisition(0, true, 12000, 0);

	// Turn the field off
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
	cmd_send(CMD_ACK,0,0,0,0,0);
	LED_A_OFF();
}

void T55xxWakeUp(uint32_t Pwd){
	LED_B_ON();
	uint32_t i = 0;

	StartTicks();

	// Set up FPGA, 125kHz
	LFSetupFPGAForADC(95, true);
	// make sure tag is fully powered up...
	WaitMS(4);

	// Trigger T55x7 Direct Access Mode
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	WaitUS(t_config.start_gap);

	// Opcode 10
	T55xxWriteBit(1);
	T55xxWriteBit(0); //Page 0

	// Send Pwd
	for (i = 0x80000000; i != 0; i >>= 1)
		T55xxWriteBit(Pwd & i);

	// Turn and leave field on to let the begin repeating transmission
	TurnReadLFOn(20*1000);
}

/*-------------- Cloning routines -----------*/
void WriteT55xx(uint32_t *blockdata, uint8_t startblock, uint8_t numblocks) {
	// write last block first and config block last (if included)
	for (uint8_t i = numblocks+startblock; i > startblock; i--)
		T55xxWriteBlockExt(blockdata[i-1], i-1, 0, 0);
}

// Copy HID id to card and setup block 0 config
void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) {
	uint32_t data[] = {0,0,0,0,0,0,0};
	uint8_t last_block = 0;

	if (longFMT){
		// Ensure no more than 84 bits supplied
		if (hi2 > 0xFFFFF) {
			DbpString("Tags can only have 84 bits.");
			return;
		}
		// Build the 6 data blocks for supplied 84bit ID
		last_block = 6;
		// load preamble (1D) & long format identifier (9E manchester encoded)
		data[1] = 0x1D96A900 | (manchesterEncode2Bytes((hi2 >> 16) & 0xF) & 0xFF);
		// load raw id from hi2, hi, lo to data blocks (manchester encoded)
		data[2] = manchesterEncode2Bytes(hi2 & 0xFFFF);
		data[3] = manchesterEncode2Bytes(hi >> 16);
		data[4] = manchesterEncode2Bytes(hi & 0xFFFF);
		data[5] = manchesterEncode2Bytes(lo >> 16);
		data[6] = manchesterEncode2Bytes(lo & 0xFFFF);
	} else {
		// Ensure no more than 44 bits supplied
		if (hi > 0xFFF) {
			DbpString("Tags can only have 44 bits.");
			return;
		}
		// Build the 3 data blocks for supplied 44bit ID
		last_block = 3;
		// load preamble
		data[1] = 0x1D000000 | (manchesterEncode2Bytes(hi) & 0xFFFFFF);
		data[2] = manchesterEncode2Bytes(lo >> 16);
		data[3] = manchesterEncode2Bytes(lo & 0xFFFF);
	}
	// load chip config block
	data[0] = T55x7_BITRATE_RF_50 | T55x7_MODULATION_FSK2a | last_block << T55x7_MAXBLOCK_SHIFT;

	//TODO add selection of chip for Q5 or T55x7
	// data[0] = T5555_SET_BITRATE(50) | T5555_MODULATION_FSK2 | T5555_INVERT_OUTPUT | last_block << T5555_MAXBLOCK_SHIFT;

	LED_D_ON();
	WriteT55xx(data, 0, last_block+1);
	LED_D_OFF();
}

void CopyIOtoT55x7(uint32_t hi, uint32_t lo) {
	uint32_t data[] = {T55x7_BITRATE_RF_64 | T55x7_MODULATION_FSK2a | (2 << T55x7_MAXBLOCK_SHIFT), hi, lo};
	//TODO add selection of chip for Q5 or T55x7
	// data[0] = T5555_SET_BITRATE(64) | T5555_MODULATION_FSK2 | T5555_INVERT_OUTPUT | 2 << T5555_MAXBLOCK_SHIFT;

	LED_D_ON();
	// Program the data blocks for supplied ID
	// and the block 0 config
	WriteT55xx(data, 0, 3);
	LED_D_OFF();
}

// Clone Indala 64-bit tag by UID to T55x7
void CopyIndala64toT55x7(uint32_t hi, uint32_t lo) {
	//Program the 2 data blocks for supplied 64bit UID
	// and the Config for Indala 64 format (RF/32;PSK2 with RF/2;Maxblock=2)
	uint32_t data[] = { T55x7_BITRATE_RF_32 | T55x7_MODULATION_PSK2 | (2 << T55x7_MAXBLOCK_SHIFT), hi, lo};
	//TODO add selection of chip for Q5 or T55x7
	// data[0] = T5555_SET_BITRATE(32 | T5555_MODULATION_PSK2 | 2 << T5555_MAXBLOCK_SHIFT;

	WriteT55xx(data, 0, 3);
	//Alternative config for Indala (Extended mode;RF/32;PSK2 with RF/2;Maxblock=2;Inverse data)
	//	T5567WriteBlock(0x603E1042,0);
}
// Clone Indala 224-bit tag by UID to T55x7
void CopyIndala224toT55x7(uint32_t uid1, uint32_t uid2, uint32_t uid3, uint32_t uid4, uint32_t uid5, uint32_t uid6, uint32_t uid7) {
	//Program the 7 data blocks for supplied 224bit UID
	uint32_t data[] = {0, uid1, uid2, uid3, uid4, uid5, uid6, uid7};
	// and the block 0 for Indala224 format
	//Config for Indala (RF/32;PSK2 with RF/2;Maxblock=7)
	data[0] = T55x7_BITRATE_RF_32 | T55x7_MODULATION_PSK2 | (7 << T55x7_MAXBLOCK_SHIFT);
	//TODO add selection of chip for Q5 or T55x7
	// data[0] =  T5555_SET_BITRATE(32 | T5555_MODULATION_PSK2 | 7 << T5555_MAXBLOCK_SHIFT;
	WriteT55xx(data, 0, 8);
	//Alternative config for Indala (Extended mode;RF/32;PSK2 with RF/2;Maxblock=7;Inverse data)
	//	T5567WriteBlock(0x603E10E2,0);
}
// clone viking tag to T55xx
void CopyVikingtoT55xx(uint32_t block1, uint32_t block2, uint8_t Q5) {
	uint32_t data[] = {T55x7_BITRATE_RF_32 | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT), block1, block2};
	if (Q5) data[0] = T5555_SET_BITRATE(32) | T5555_MODULATION_MANCHESTER | 2 << T5555_MAXBLOCK_SHIFT;
	// Program the data blocks for supplied ID and the block 0 config
	WriteT55xx(data, 0, 3);
	LED_D_OFF();
	cmd_send(CMD_ACK,0,0,0,0,0);
}

// Define 9bit header for EM410x tags
#define EM410X_HEADER		0x1FF
#define EM410X_ID_LENGTH	40

void WriteEM410x(uint32_t card, uint32_t id_hi, uint32_t id_lo) {
	int i, id_bit;
	uint64_t id = EM410X_HEADER;
	uint64_t rev_id = 0;	// reversed ID
	int c_parity[4];	// column parity
	int r_parity = 0;	// row parity
	uint32_t clock = 0;

	// Reverse ID bits given as parameter (for simpler operations)
	for (i = 0; i < EM410X_ID_LENGTH; ++i) {
		if (i < 32) {
			rev_id = (rev_id << 1) | (id_lo & 1);
			id_lo >>= 1;
		} else {
			rev_id = (rev_id << 1) | (id_hi & 1);
			id_hi >>= 1;
		}
	}

	for (i = 0; i < EM410X_ID_LENGTH; ++i) {
		id_bit = rev_id & 1;

		if (i % 4 == 0) {
			// Don't write row parity bit at start of parsing
			if (i)
				id = (id << 1) | r_parity;
			// Start counting parity for new row
			r_parity = id_bit;
		} else {
			// Count row parity
			r_parity ^= id_bit;
		}

		// First elements in column?
		if (i < 4)
			// Fill out first elements
			c_parity[i] = id_bit;
		else
			// Count column parity
			c_parity[i % 4] ^= id_bit;

		// Insert ID bit
		id = (id << 1) | id_bit;
		rev_id >>= 1;
	}

	// Insert parity bit of last row
	id = (id << 1) | r_parity;

	// Fill out column parity at the end of tag
	for (i = 0; i < 4; ++i)
		id = (id << 1) | c_parity[i];

	// Add stop bit
	id <<= 1;

	Dbprintf("Started writing %s tag ...", card ? "T55x7":"T5555");
	LED_D_ON();

	// Write EM410x ID
	uint32_t data[] = {0, (uint32_t)(id>>32), (uint32_t)(id & 0xFFFFFFFF)};

	clock = (card & 0xFF00) >> 8;
	clock = (clock == 0) ? 64 : clock;
	Dbprintf("Clock rate: %d", clock);
	if (card & 0xFF) { //t55x7
		clock = GetT55xxClockBit(clock);
		if (clock == 0) {
			Dbprintf("Invalid clock rate: %d", clock);
			return;
		}
		data[0] = clock | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT);
	} else { //t5555 (Q5)
		data[0] = T5555_SET_BITRATE(clock) | T5555_MODULATION_MANCHESTER | (2 << T5555_MAXBLOCK_SHIFT);
	}

	WriteT55xx(data, 0, 3);

	LED_D_OFF();
	Dbprintf("Tag %s written with 0x%08x%08x\n",
			card ? "T55x7":"T5555",
			(uint32_t)(id >> 32),
			(uint32_t)id);
}

//-----------------------------------
// EM4469 / EM4305 routines
//-----------------------------------
// Below given command set.
// Commands are including the even parity, binary mirrored
#define FWD_CMD_LOGIN   0xC
#define FWD_CMD_WRITE   0xA
#define FWD_CMD_READ    0x9
#define FWD_CMD_DISABLE 0x5

uint8_t forwardLink_data[64]; //array of forwarded bits
uint8_t * forward_ptr; //ptr for forward message preparation
uint8_t fwd_bit_sz; //forwardlink bit counter
uint8_t * fwd_write_ptr; //forwardlink bit pointer

//====================================================================
// prepares command bits
// see EM4469 spec
//====================================================================
//--------------------------------------------------------------------
//  VALUES TAKEN FROM EM4x function: SendForward
//  START_GAP = 440;       (55*8) cycles at 125Khz (8us = 1cycle)
//  WRITE_GAP = 128;       (16*8)
//  WRITE_1   = 256 32*8;  (32*8)

//  These timings work for 4469/4269/4305 (with the 55*8 above)
//  WRITE_0 = 23*8 , 9*8

uint8_t Prepare_Cmd( uint8_t cmd ) {

	*forward_ptr++ = 0; //start bit
	*forward_ptr++ = 0; //second pause for 4050 code

	*forward_ptr++ = cmd;
	cmd >>= 1;
	*forward_ptr++ = cmd;
	cmd >>= 1;
	*forward_ptr++ = cmd;
	cmd >>= 1;
	*forward_ptr++ = cmd;

	return 6; //return number of emited bits
}

//====================================================================
// prepares address bits
// see EM4469 spec
//====================================================================
uint8_t Prepare_Addr( uint8_t addr ) {

	register uint8_t line_parity;

	uint8_t i;
	line_parity = 0;
	for( i=0; i<6; i++ ) {
		*forward_ptr++ = addr;
		line_parity ^= addr;
		addr >>= 1;
	}

	*forward_ptr++ = (line_parity & 1);

	return 7; //return number of emited bits
}

//====================================================================
// prepares data bits intreleaved with parity bits
// see EM4469 spec
//====================================================================
uint8_t Prepare_Data( uint16_t data_low, uint16_t data_hi) {

	register uint8_t line_parity;
	register uint8_t column_parity;
	register uint8_t i, j;
	register uint16_t data;

	data = data_low;
	column_parity = 0;

	for(i=0; i<4; i++) {
		line_parity = 0;
		for(j=0; j<8; j++) {
			line_parity ^= data;
			column_parity ^= (data & 1) << j;
			*forward_ptr++ = data;
			data >>= 1;
		}
		*forward_ptr++ = line_parity;
		if(i == 1)
			data = data_hi;
	}

	for(j=0; j<8; j++) {
		*forward_ptr++ = column_parity;
		column_parity >>= 1;
	}
	*forward_ptr = 0;

	return 45; //return number of emited bits
}

//====================================================================
// Forward Link send function
// Requires: forwarLink_data filled with valid bits (1 bit per byte)
// fwd_bit_count set with number of bits to be sent
//====================================================================
void SendForward(uint8_t fwd_bit_count) {

// iceman,   21.3us increments for the USclock verification.
// 55FC * 8us == 440us / 21.3 === 20.65 steps.  could be too short. Go for 56FC instead
// 32FC * 8us == 256us / 21.3 ==  12.018 steps. ok
// 16FC * 8us == 128us / 21.3 ==  6.009 steps. ok
#ifndef EM_START_GAP
#define EM_START_GAP 55*8
#endif

	fwd_write_ptr = forwardLink_data;
	fwd_bit_sz = fwd_bit_count;

	// Set up FPGA, 125kHz or 95 divisor
	LFSetupFPGAForADC(95, true);

	// force 1st mod pulse (start gap must be longer for 4305)
	fwd_bit_sz--; //prepare next bit modulation
	fwd_write_ptr++;

	TurnReadLF_off(EM_START_GAP);
	TurnReadLFOn(18*8);

	// now start writting with bitbanging the antenna.
	while(fwd_bit_sz-- > 0) { //prepare next bit modulation
		if(((*fwd_write_ptr++) & 1) == 1) {
			WaitUS(32*8);
		} else {
			TurnReadLF_off(23*8);
			TurnReadLFOn(18*8);
		}
	}
}

void EM4xLogin(uint32_t pwd) {
	uint8_t len;
	forward_ptr = forwardLink_data;
	len = Prepare_Cmd( FWD_CMD_LOGIN );
	len += Prepare_Data( pwd & 0xFFFF, pwd >> 16 );
	SendForward(len);
	//WaitUS(20); // no wait for login command.
	// should receive
	// 0000 1010 ok.
	// 0000 0001 fail
}

void EM4xReadWord(uint8_t addr, uint32_t pwd, uint8_t usepwd) {

	LED_A_ON();
	uint8_t len;

	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_ext(false);

	StartTicks();
	/* should we read answer from Logincommand?
	*
	* should receive
	* 0000 1010 ok.
	* 0000 0001 fail
	**/
	if (usepwd) EM4xLogin(pwd);

	forward_ptr = forwardLink_data;
	len = Prepare_Cmd( FWD_CMD_READ );
	len += Prepare_Addr( addr );

	SendForward(len);

	WaitUS(400);

	DoPartialAcquisition(20, true, 6000, 1000);

	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	cmd_send(CMD_ACK,0,0,0,0,0);
	LED_A_OFF();
}

void EM4xWriteWord(uint32_t flag, uint32_t data, uint32_t pwd) {

	LED_A_ON();

	bool usePwd = (flag & 0xF);
	uint8_t addr = (flag >> 8) & 0xFF;
	uint8_t len;

	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_ext(false);
	StartTicks();
	/* should we read answer from Logincommand?
	*
	* should receive
	* 0000 1010 ok.
	* 0000 0001 fail
	**/
	if (usePwd) EM4xLogin(pwd);

	forward_ptr = forwardLink_data;
	len = Prepare_Cmd( FWD_CMD_WRITE );
	len += Prepare_Addr( addr );
	len += Prepare_Data( data & 0xFFFF, data >> 16 );

	SendForward(len);

	//Wait 20ms for write to complete?
	WaitMS(7);

	//Capture response if one exists
	DoPartialAcquisition(20, true, 6000, 1000);

	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
	cmd_send(CMD_ACK,0,0,0,0,0);
	LED_A_OFF();
}

/*
Reading a COTAG.

COTAG needs the reader to send a startsequence and the card has an extreme slow datarate.
because of this, we can "sample" the data signal but we interpreate it to Manchester direct.

READER START SEQUENCE:
burst 800 us,    gap   2.2 msecs
burst 3.6 msecs  gap   2.2 msecs
burst 800 us     gap   2.2 msecs
pulse 3.6 msecs

This triggers a COTAG tag to response
*/
void Cotag(uint32_t arg0) {
#ifndef OFF
# define OFF 	{ FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); WaitUS(2035); }
#endif
#ifndef ON
# define ON(x)   { FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); WaitUS((x)); }
#endif
	uint8_t rawsignal = arg0 & 0xF;

	LED_A_ON();

	// Switching to LF image on FPGA. This might empty BigBuff
	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);

	//clear buffer now so it does not interfere with timing later
	BigBuf_Clear_ext(false);

	// Set up FPGA, 132kHz to power up the tag
	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 89);
	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);

	// Connect the A/D to the peak-detected low-frequency path.
	SetAdcMuxFor(GPIO_MUXSEL_LOPKD);

	// Now set up the SSC to get the ADC samples that are now streaming at us.
	FpgaSetupSsc();

	// start clock - 1.5ticks is 1us
	StartTicks();

	//send COTAG start pulse
	ON(740)  OFF
	ON(3330) OFF
	ON(740)  OFF
	ON(1000)

	switch(rawsignal) {
		case 0: doCotagAcquisition(50000); break;
		case 1: doCotagAcquisitionManchester(); break;
		case 2: DoAcquisition_config(true, 0); break;
	}

	// Turn the field off
	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
	cmd_send(CMD_ACK,0,0,0,0,0);
	LEDsoff();
}

/*
* EM4305 support
*/