RfidResearchGroup/proxmark3
1
1
Fork 0
mirror of https://github.com/RfidResearchGroup/proxmark3.git synced 2024-12-31 04:39:49 +08:00
Code Issues Projects Releases Packages Wiki Activity
proxmark3/common_arm/usb_cdc.c
Philippe Teuwen cb8d589fc4 armsrc: clarify static vars vs global vars, part 3
2020-05-19 18:12:40 +02:00

1038 lines
38 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*
* at91sam7s USB CDC device implementation
*
* Copyright (c) 2012, Roel Verdult
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holders nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* based on the "Basic USB Example" from ATMEL (doc6123.pdf)
*
* @file usb_cdc.c
* @brief
*/
#include "usb_cdc.h"
#include "proxmark3_arm.h"
#include "usart_defs.h"
/*
AT91SAM7S256 USB Device Port
• Embedded 328-byte dual-port RAM for endpoints
• Four endpoints
– Endpoint 0: 8 bytes
– Endpoint 1 and 2: 64 bytes ping-pong
– Endpoint 3: 64 bytes
– Ping-pong Mode (two memory banks) for bulk endpoints
*/
//
#define AT91C_EP_CONTROL 0
#define AT91C_EP_OUT 1 // cfg bulk out
#define AT91C_EP_IN 2 // cfg bulk in
#define AT91C_EP_NOTIFY 3 // cfg cdc notification interrup
#define AT91C_EP_CONTROL_SIZE 8
#define AT91C_EP_OUT_SIZE 64
#define AT91C_EP_IN_SIZE 64
// Section: USB Descriptors
#define USB_DESCRIPTOR_DEVICE 0x01 // DescriptorType for a Device Descriptor.
#define USB_DESCRIPTOR_CONFIGURATION 0x02 // DescriptorType for a Configuration Descriptor.
#define USB_DESCRIPTOR_STRING 0x03 // DescriptorType for a String Descriptor.
#define USB_DESCRIPTOR_INTERFACE 0x04 // DescriptorType for an Interface Descriptor.
#define USB_DESCRIPTOR_ENDPOINT 0x05 // DescriptorType for an Endpoint Descriptor.
#define USB_DESCRIPTOR_DEVICE_QUALIFIER 0x06 // DescriptorType for a Device Qualifier.
#define USB_DESCRIPTOR_OTHER_SPEED 0x07 // DescriptorType for a Other Speed Configuration.
#define USB_DESCRIPTOR_INTERFACE_POWER 0x08 // DescriptorType for Interface Power.
#define USB_DESCRIPTOR_OTG 0x09 // DescriptorType for an OTG Descriptor.
#define USB_DESCRIPTOR_IAD 0x0B // DescriptorType for a Interface Association Descriptor
#define USB_DESCRIPTOR_TYPE_BO 0x0F // DescriptorType for a BOS Descriptor.
/* Configuration Attributes */
#define _DEFAULT (0x01<<7) //Default Value (Bit 7 is set)
#define _SELF (0x01<<6) //Self-powered (Supports if set)
#define _RWU (0x01<<5) //Remote Wakeup (Supports if set)
#define _HNP (0x01 << 1) //HNP (Supports if set)
#define _SRP (0x01) //SRP (Supports if set)
/* Endpoint Transfer Type */
#define _CTRL 0x00 //Control Transfer
#define _ISO 0x01 //Isochronous Transfer
#define _BULK 0x02 //Bulk Transfer
#define _INTERRUPT 0x03 //Interrupt Transfer
// (bit7 | 0 = OUT, 1 = IN)
#define _EP_IN 0x80
#define _EP_OUT 0x00
#define _EP01_OUT 0x01
#define _EP01_IN 0x81
#define _EP02_OUT 0x02
#define _EP02_IN 0x82
#define _EP03_OUT 0x03
#define _EP03_IN 0x83
/* WCID specific Request Code */
#define MS_OS_DESCRIPTOR_INDEX 0xEE
#define MS_VENDOR_CODE 0x1C
#define MS_EXTENDED_COMPAT_ID 0x04
#define MS_EXTENDED_PROPERTIES 0x05
#define MS_WCID_GET_DESCRIPTOR 0xC0
#define MS_WCID_GET_FEATURE_DESCRIPTOR 0xC1
/* USB standard request code */
#define STD_GET_STATUS_ZERO 0x0080
#define STD_GET_STATUS_INTERFACE 0x0081
#define STD_GET_STATUS_ENDPOINT 0x0082
#define STD_CLEAR_FEATURE_ZERO 0x0100
#define STD_CLEAR_FEATURE_INTERFACE 0x0101
#define STD_CLEAR_FEATURE_ENDPOINT 0x0102
#define STD_SET_FEATURE_ZERO 0x0300
#define STD_SET_FEATURE_INTERFACE 0x0301
#define STD_SET_FEATURE_ENDPOINT 0x0302
#define STD_SET_ADDRESS 0x0500
#define STD_GET_DESCRIPTOR 0x0680
#define STD_SET_DESCRIPTOR 0x0700
#define STD_GET_CONFIGURATION 0x0880
#define STD_SET_CONFIGURATION 0x0900
#define STD_GET_INTERFACE 0x0A81
#define STD_SET_INTERFACE 0x0B01
#define STD_SYNCH_FRAME 0x0C82
/* CDC Class Specific Request Code */
#define GET_LINE_CODING 0x21A1
#define SET_LINE_CODING 0x2021
#define SET_CONTROL_LINE_STATE 0x2221
AT91PS_UDP pUdp = AT91C_BASE_UDP;
static uint8_t btConfiguration = 0;
static uint8_t btConnection = 0;
static uint8_t btReceiveBank = AT91C_UDP_RX_DATA_BK0;
static const char devDescriptor[] = {
/* Device descriptor */
0x12, // Length
USB_DESCRIPTOR_DEVICE, // Descriptor Type (DEVICE)
0x00, 0x02, // Complies with USB Spec. Release (0200h = release 2.00) 0210 == release 2.10
2, // Device Class: Communication Device Class
0, // Device Subclass: CDC class sub code ACM [ice 0x02 = win10 virtual comport ]
0, // Device Protocol: CDC Device protocol (unused)
AT91C_EP_CONTROL_SIZE, // MaxPacketSize0
0xc4, 0x9a, // Vendor ID [0x9ac4 = J. Westhues]
0x8f, 0x4b, // Product ID [0x4b8f = Proxmark-3 RFID Instrument]
0x00, 0x01, // BCD Device release number (1.00)
1, // index Manufacturer
2, // index Product
3, // index SerialNumber
1 // Number of Configs
};
static const char cfgDescriptor[] = {
/* Configuration 1 descriptor */
// -----------------------------
9, // Length
USB_DESCRIPTOR_CONFIGURATION, // Descriptor Type
(9 + 9 + 5 + 5 + 4 + 5 + 7 + 9 + 7 + 7), 0, // Total Length 2 EP + Control
2, // Number of Interfaces
1, // Index value of this Configuration (used in SetConfiguration from Host)
0, // Configuration string index
_DEFAULT, // Attributes 0xA0
0xFA, // Max Power consumption
// IAD to associate the one CDC interface
// --------------------------------------
/*
8, // Length
USB_DESCRIPTOR_IAD, // IAD_DESCRIPTOR (0x0B)
0, // CDC_INT_INTERFACE NUMBER (
2, // IAD INTERFACE COUNT (two interfaces)
2, // Function Class: CDC_CLASS
2, // Function SubClass: ACM
1, // Function Protocol: v.25term
0, // iInterface
*/
/* Interface 0 Descriptor */
/* CDC Communication Class Interface Descriptor Requirement for Notification*/
// -----------------------------------------------------------
9, // Length
USB_DESCRIPTOR_INTERFACE, // Descriptor Type
0, // Interface Number
0, // Alternate Setting
1, // Number of Endpoints in this interface
2, // Interface Class code (Communication Interface Class)
2, // Interface Subclass code (Abstract Control Model)
1, // InterfaceProtocol (Common AT Commands, V.25term)
0, // iInterface
/* Header Functional Descriptor */
5, // Function Length
0x24, // Descriptor type: CS_INTERFACE
0, // Descriptor subtype: Header Functional Descriptor
0x10, 0x01, // bcd CDC:1.1
/* ACM Functional Descriptor */
4, // Function Length
0x24, // Descriptor Type: CS_INTERFACE
2, // Descriptor Subtype: Abstract Control Management Functional Descriptor
2, // Capabilities D1, Device supports the request combination of Set_Line_Coding, Set_Control_Line_State, Get_Line_Coding, and the notification Serial_State
/* Union Functional Descriptor */
5, // Function Length
0x24, // Descriptor Type: CS_INTERFACE
6, // Descriptor Subtype: Union Functional Descriptor
0, // MasterInterface: Communication Class Interface
1, // SlaveInterface0: Data Class Interface
/* Call Management Functional Descriptor */
5, // Function Length
0x24, // Descriptor Type: CS_INTERFACE
1, // Descriptor Subtype: Call Management Functional Descriptor
0, // Capabilities: Device sends/receives call management information only over the Communication Class interface. Device does not handle call management itself
1, // Data Interface: Data Class Interface
/* Protocol Functional Descriptor */
/*
6,
0x24, // Descriptor Type: CS_INTERFACE
0x0B, // Descriptor Subtype: Protocol Unit functional Descriptor
0xDD, // constant uniq ID of unit
0xFE, // protocol
*/
/* CDC Notification Endpoint descriptor */
// ---------------------------------------
7, // Length
USB_DESCRIPTOR_ENDPOINT, // Descriptor Type
_EP03_IN, // EndpointAddress: Endpoint 03 - IN
_INTERRUPT, // Attributes
AT91C_EP_CONTROL_SIZE, 0x00, // MaxPacket Size: EP0 - 8
0xFF, // Interval polling
/* Interface 1 Descriptor */
/* CDC Data Class Interface 1 Descriptor Requirement */
9, // Length
USB_DESCRIPTOR_INTERFACE, // Descriptor Type
1, // Interface Number
0, // Alternate Setting
2, // Number of Endpoints
0x0A, // Interface Class: CDC Data interface class
0, // Interface Subclass: not used
0, // Interface Protocol: No class specific protocol required (usb spec)
0, // Interface
/* Endpoint descriptor */
7, // Length
USB_DESCRIPTOR_ENDPOINT, // Descriptor Type
_EP01_OUT, // Endpoint Address: Endpoint 01 - OUT
_BULK, // Attributes: BULK
AT91C_EP_OUT_SIZE, 0x00, // MaxPacket Size: 64 bytes
0, // Interval: ignored for bulk
/* Endpoint descriptor */
7, // Length
USB_DESCRIPTOR_ENDPOINT, // Descriptor Type
_EP02_IN, // Endpoint Address: Endpoint 02 - IN
_BULK, // Attribute: BULK
AT91C_EP_IN_SIZE, 0x00, // MaxPacket Size: 64 bytes
0 // Interval: ignored for bulk
};
// BOS descriptor
static const char bosDescriptor[] = {
0x5,
USB_DESCRIPTOR_TYPE_BO,
0xC,
0x0,
0x1, // 1 device capability
0x7,
0x10, // USB_DEVICE_CAPABITY_TYPE,
0x2,
0x2, // LPM capability bit set
0x0,
0x0,
0x0
};
// Microsoft OS Extended Configuration Compatible ID Descriptor
/*
static const char CompatIDFeatureDescriptor[] = {
0x28, 0x00, 0x00, 0x00, // Descriptor Length 40bytes (0x28)
0x00, 0x01, // Version ('1.0')
MS_EXTENDED_COMPAT_ID, 0x00, // Compatibility ID Descriptor Index 0x0004
0x01, // Number of sections. 0x1
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Reserved (7bytes)
// -----function section 1------
0x00, // Interface Number #0
0x01, // reserved (0x1)
0x57, 0x49, 0x4E, 0x55, 0x53, 0x42, 0x00, 0x00, // Compatible ID ('WINUSB\0\0') (8bytes)
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Sub-Compatible ID (8byte)
0x00, 0x00, 0x00, 0x00, 0x00, 0x00 // Reserved (6bytes)
};
*/
// Microsoft Extended Properties Feature Descriptor
/*
static const char OSprop[] = {
// u32 Descriptor Length (10+132+64+102 == 308
0x34, 0x01, 0, 0,
// u16 Version ('1.0')
0, 1,
// u16 wIndex
MS_EXTENDED_PROPERTIES, 0,
// u16 wCount -- three section
3, 0,
// -----property section 1------
// u32 size ( 14+40+78 == 132)
132, 0, 0, 0,
// u32 type
1, 0, 0, 0, // unicode string
// u16 namelen (20*2 = 40)
40, 0,
// name DeviceInterfaceGUID
'D',0,'e',0,'v',0,'i',0,'c',0,'e',0,'I',0,'n',0,'t',0,'e',0,'r',0,'f',0,'a',0,'c',0,'e',0,'G',0,'U',0,'I',0,'D',0,0,0,
// u32 datalen (39*2 = 78)
78, 0, 0, 0,
// data {4D36E978-E325-11CE-BFC1-08002BE10318}
'{',0,'4',0,'d',0,'3',0,'6',0,'e',0,'9',0,'7',0,'8',0,'-',0,'e',0,'3',0,'2',0,'5',0,
'-',0,'1',0,'1',0,'c',0,'e',0,'-',0,'b',0,'f',0,'c',0,'1',0,'-',0,'0',0,'8',0,'0',0,
'0',0,'2',0,'b',0,'e',0,'1',0,'0',0,'3',0,'1',0,'8',0,'}',0,0,0,
// -----property section 2------
// u32 size ( 14+12+38 == 64)
64, 0, 0, 0,
// u32 type
1, 0, 0, 0, // unicode string
// u16 namelen (12)
12, 0,
// name Label
'L',0,'a',0,'b',0,'e',0,'l',0,0,0,
// u32 datalen ( 19*2 = 38 )
38, 0, 0, 0,
// data 'Awesome PM3 Device'
'A',0,'w',0,'e',0,'s',0,'o',0,'m',0,'e',0,' ',0,'P',0,'M',0,'3',0,' ',0,'D',0,'e',0,'v',0,'i',0,'c',0,'e',0,0,0,
// -----property section 3------
// u32 size ( 14+12+76 == 102)
102, 0, 0, 0,
// u32 type
2, 0, 0, 0, //Unicode string with environment variables
// u16 namelen (12)
12, 0,
// name Icons
'I',0,'c',0,'o',0,'n',0,'s',0,0,0,
// u32 datalen ( 38*2 == 76)
76, 0, 0, 0,
// data '%SystemRoot%\\system32\\Shell32.dll,-13'
'%',0,'S',0,'y',0,'s',0,'t',0,'e',0,'m',0,'R',0,'o',0,'o',0,'t',0,'%',0,
'\\',0,'s',0,'y',0,'s',0,'t',0,'e',0,'m',0,'3',0,'2',0,'\\',0,
'S',0,'h',0,'e',0,'l',0,'l',0,'3',0,'2',0,'.',0,'d',0,'l',0,'l',0,',',0,
'-',0,'1',0,'3',0,0,0
};
*/
static const char StrLanguageCodes[] = {
4, // Length
0x03, // Type is string
0x09, 0x04 // supported language Code 0 = 0x0409 (English)
};
// Note: ModemManager (Linux) ignores Proxmark3 devices by matching the
// manufacturer string "proxmark.org". Don't change this.
// or use the blacklisting file.
static const char StrManufacturer[] = {
26, // Length
0x03, // Type is string
'p', 0, 'r', 0, 'o', 0, 'x', 0, 'm', 0, 'a', 0, 'r', 0, 'k', 0, '.', 0, 'o', 0, 'r', 0, 'g', 0,
};
static const char StrProduct[] = {
20, // Length
0x03, // Type is string
'p', 0, 'r', 0, 'o', 0, 'x', 0, 'm', 0, 'a', 0, 'r', 0, 'k', 0, '3', 0
};
static const char StrSerialNumber[] = {
14, // Length
0x03, // Type is string
'i', 0, 'c', 0, 'e', 0, 'm', 0, 'a', 0, 'n', 0
};
// size includes their own field.
static const char StrMS_OSDescriptor[] = {
18, // length 0x12
0x03, // Type is string
'M', 0, 'S', 0, 'F', 0, 'T', 0, '1', 0, '0', 0, '0', 0, MS_VENDOR_CODE, 0
};
static const char *getStringDescriptor(uint8_t idx) {
switch (idx) {
case 0:
return StrLanguageCodes;
case 1:
return StrManufacturer;
case 2:
return StrProduct;
case 3:
return StrSerialNumber;
case MS_OS_DESCRIPTOR_INDEX:
return StrMS_OSDescriptor;
default:
return (NULL);
}
}
// Bitmap for all status bits in CSR which must be written as 1 to cause no effect
#define REG_NO_EFFECT_1_ALL AT91C_UDP_RX_DATA_BK0 | AT91C_UDP_RX_DATA_BK1 \
|AT91C_UDP_STALLSENT | AT91C_UDP_RXSETUP \
|AT91C_UDP_TXCOMP
// Clear flags in the UDP_CSR register and waits for synchronization
#define UDP_CLEAR_EP_FLAGS(endpoint, flags) { \
volatile unsigned int reg; \
reg = pUdp->UDP_CSR[(endpoint)]; \
reg |= REG_NO_EFFECT_1_ALL; \
reg &= ~(flags); \
pUdp->UDP_CSR[(endpoint)] = reg; \
}
// reset flags in the UDP_CSR register and waits for synchronization
#define UDP_SET_EP_FLAGS(endpoint, flags) { \
volatile unsigned int reg; \
reg = pUdp->UDP_CSR[(endpoint)]; \
reg |= REG_NO_EFFECT_1_ALL; \
reg |= (flags); \
pUdp->UDP_CSR[(endpoint)] = reg; \
}
typedef struct {
uint32_t BitRate;
uint8_t Format;
uint8_t ParityType;
uint8_t DataBits;
} AT91S_CDC_LINE_CODING, *AT91PS_CDC_LINE_CODING;
AT91S_CDC_LINE_CODING line = { // purely informative, actual values don't matter
USART_BAUD_RATE, // baudrate
0, // 1 Stop Bit
0, // None Parity
8 // 8 Data bits
};
// timer counts in 21.3us increments (1024/48MHz), rounding applies
// WARNING: timer can't measure more than 1.39s (21.3us * 0xffff)
static void SpinDelayUs(int us) {
int ticks = ((MCK / 1000000) * us + 512) >> 10;
// Borrow a PWM unit for my real-time clock
AT91C_BASE_PWMC->PWMC_ENA = PWM_CHANNEL(0);
// 48 MHz / 1024 gives 46.875 kHz
AT91C_BASE_PWMC_CH0->PWMC_CMR = PWM_CH_MODE_PRESCALER(10); // Channel Mode Register
AT91C_BASE_PWMC_CH0->PWMC_CDTYR = 0; // Channel Duty Cycle Register
AT91C_BASE_PWMC_CH0->PWMC_CPRDR = 0xffff; // Channel Period Register
uint16_t start = AT91C_BASE_PWMC_CH0->PWMC_CCNTR;
for (;;) {
uint16_t now = AT91C_BASE_PWMC_CH0->PWMC_CCNTR;
if (now == (uint16_t)(start + ticks))
return;
WDT_HIT();
}
}
/*
*----------------------------------------------------------------------------
* \fn usb_disable
* \brief This function deactivates the USB device
*----------------------------------------------------------------------------
*/
void usb_disable(void) {
// Disconnect the USB device
AT91C_BASE_PIOA->PIO_ODR = GPIO_USB_PU;
// Clear all lingering interrupts
if (pUdp->UDP_ISR & AT91C_UDP_ENDBUSRES) {
pUdp->UDP_ICR = AT91C_UDP_ENDBUSRES;
}
}
/*
*----------------------------------------------------------------------------
* \fn usb_enable
* \brief This function Activates the USB device
*----------------------------------------------------------------------------
*/
void usb_enable(void) {
// Set the PLL USB Divider
AT91C_BASE_CKGR->CKGR_PLLR |= AT91C_CKGR_USBDIV_1 ;
// Specific Chip USB Initialisation
// Enables the 48MHz USB clock UDPCK and System Peripheral USB Clock
AT91C_BASE_PMC->PMC_SCER |= AT91C_PMC_UDP;
AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_UDP);
AT91C_BASE_UDP->UDP_FADDR = 0;
AT91C_BASE_UDP->UDP_GLBSTATE = 0;
// Enable UDP PullUp (USB_DP_PUP) : enable & Clear of the corresponding PIO
// Set in PIO mode and Configure in Output
AT91C_BASE_PIOA->PIO_PER = GPIO_USB_PU; // Set in PIO mode
AT91C_BASE_PIOA->PIO_OER = GPIO_USB_PU; // Configure as Output
// Clear for set the Pullup resistor
AT91C_BASE_PIOA->PIO_CODR = GPIO_USB_PU;
// Disconnect and reconnect USB controller for 100ms
usb_disable();
SpinDelayUs(100 * 1000);
// Wait for a short while
//for (volatile size_t i=0; i<0x100000; i++) {};
// Reconnect USB reconnect
AT91C_BASE_PIOA->PIO_SODR = GPIO_USB_PU;
AT91C_BASE_PIOA->PIO_OER = GPIO_USB_PU;
}
/*
*----------------------------------------------------------------------------
* \fn usb_check
* \brief Test if the device is configured and handle enumeration
*----------------------------------------------------------------------------
*/
static int usb_reconnect = 0;
static int usb_configured = 0;
void SetUSBreconnect(int value) {
usb_reconnect = value;
}
int GetUSBreconnect(void) {
return usb_reconnect;
}
void SetUSBconfigured(int value) {
usb_configured = value;
}
int GetUSBconfigured(void) {
return usb_configured;
}
bool usb_check(void) {
/*
// reconnected ONCE and
if ( !USB_ATTACHED() ){
usb_reconnect = 1;
return false;
}
// only one time after USB been disengaged and re-engaged
if ( USB_ATTACHED() && usb_reconnect == 1 ) {
if ( usb_configured == 0) {
usb_disable();
usb_enable();
AT91F_CDC_Enumerate();
usb_configured = 1;
return false;
}
}
*/
// interrupt status register
AT91_REG isr = pUdp->UDP_ISR;
// end of bus reset
if (isr & AT91C_UDP_ENDBUSRES) {
pUdp->UDP_ICR = AT91C_UDP_ENDBUSRES;
// reset all endpoints
pUdp->UDP_RSTEP = (unsigned int) - 1;
pUdp->UDP_RSTEP = 0;
// Enable the function
pUdp->UDP_FADDR = AT91C_UDP_FEN;
// Configure endpoint 0 (enable control endpoint)
pUdp->UDP_CSR[AT91C_EP_CONTROL] = (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_CTRL);
} else if (isr & AT91C_UDP_EPINT0) {
pUdp->UDP_ICR = AT91C_UDP_EPINT0;
AT91F_CDC_Enumerate();
}
/*
else if (isr & AT91C_UDP_EPINT3 ) {
pUdp->UDP_ICR = AT91C_UDP_EPINT3;
AT91F_CDC_Enumerate();
//pUdp->UDP_ICR |= AT91C_UDP_EPINT3;
}
*/
return (btConfiguration) ? true : false;
}
bool usb_poll(void) {
if (!usb_check()) return false;
return (pUdp->UDP_CSR[AT91C_EP_OUT] & btReceiveBank);
}
/**
In github PR #129, some users appears to get a false positive from
usb_poll, which returns true, but the usb_read operation
still returns 0.
This check is basically the same as above, but also checks
that the length available to read is non-zero, thus hopefully fixes the
bug.
**/
bool usb_poll_validate_length(void) {
if (!usb_check()) return false;
if (!(pUdp->UDP_CSR[AT91C_EP_OUT] & btReceiveBank)) return false;
return ((pUdp->UDP_CSR[AT91C_EP_OUT] & AT91C_UDP_RXBYTECNT) >> 16) > 0;
}
/*
*----------------------------------------------------------------------------
* \fn usb_read
* \brief Read available data from Endpoint 1 OUT (host to device)
*----------------------------------------------------------------------------
*/
uint32_t usb_read(uint8_t *data, size_t len) {
if (len == 0) return 0;
uint8_t bank = btReceiveBank;
uint32_t packetSize, nbBytesRcv = 0;
uint32_t time_out = 0;
while (len) {
if (!usb_check()) break;
if (pUdp->UDP_CSR[AT91C_EP_OUT] & bank) {
packetSize = (pUdp->UDP_CSR[AT91C_EP_OUT] & AT91C_UDP_RXBYTECNT) >> 16;
packetSize = MIN(packetSize, len);
len -= packetSize;
while (packetSize--)
data[nbBytesRcv++] = pUdp->UDP_FDR[AT91C_EP_OUT];
// flip bank
UDP_CLEAR_EP_FLAGS(AT91C_EP_OUT, bank)
if (bank == AT91C_UDP_RX_DATA_BK0)
bank = AT91C_UDP_RX_DATA_BK1;
else
bank = AT91C_UDP_RX_DATA_BK0;
}
if (time_out++ == 0x1fff) break;
}
btReceiveBank = bank;
return nbBytesRcv;
}
static uint8_t usb_read_ng_buffer[64];
static size_t usb_read_ng_bufoff = 0;
static size_t usb_read_ng_buflen = 0;
uint32_t usb_read_ng(uint8_t *data, size_t len) {
if (len == 0) return 0;
uint8_t bank = btReceiveBank;
uint32_t packetSize, nbBytesRcv = 0;
uint32_t time_out = 0;
// take first from local buffer
if (len <= usb_read_ng_buflen) {
for (uint32_t i = 0; i < len; i++)
data[nbBytesRcv++] = usb_read_ng_buffer[usb_read_ng_bufoff + i];
usb_read_ng_buflen -= len;
if (usb_read_ng_buflen == 0)
usb_read_ng_bufoff = 0;
else
usb_read_ng_bufoff += len;
return nbBytesRcv;
} else {
for (uint32_t i = 0; i < usb_read_ng_buflen; i++)
data[nbBytesRcv++] = usb_read_ng_buffer[usb_read_ng_bufoff + i];
len -= usb_read_ng_buflen;
usb_read_ng_buflen = 0;
usb_read_ng_bufoff = 0;
}
while (len) {
if (!usb_check()) break;
if ((pUdp->UDP_CSR[AT91C_EP_OUT] & bank)) {
uint32_t available = (pUdp->UDP_CSR[AT91C_EP_OUT] & AT91C_UDP_RXBYTECNT) >> 16;
packetSize = MIN(available, len);
available -= packetSize;
len -= packetSize;
while (packetSize--)
data[nbBytesRcv++] = pUdp->UDP_FDR[AT91C_EP_OUT];
// fill the local buffer with the remaining bytes
for (uint32_t i = 0; i < available; i++)
usb_read_ng_buffer[i] = pUdp->UDP_FDR[AT91C_EP_OUT];
usb_read_ng_buflen = available;
// flip bank
UDP_CLEAR_EP_FLAGS(AT91C_EP_OUT, bank)
if (bank == AT91C_UDP_RX_DATA_BK0)
bank = AT91C_UDP_RX_DATA_BK1;
else
bank = AT91C_UDP_RX_DATA_BK0;
}
if (time_out++ == 0x1fff) break;
}
btReceiveBank = bank;
return nbBytesRcv;
}
/*
*----------------------------------------------------------------------------
* \fn usb_write
* \brief Send through endpoint 2 (device to host)
*----------------------------------------------------------------------------
*/
int usb_write(const uint8_t *data, const size_t len) {
if (!len) return PM3_EINVARG;
if (!usb_check()) return PM3_EIO;
// can we write?
if ((pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXPKTRDY) != 0) return PM3_EIO;
size_t length = len;
uint32_t cpt = 0;
// send first chunk
cpt = MIN(length, AT91C_EP_IN_SIZE);
length -= cpt;
while (cpt--) {
pUdp->UDP_FDR[AT91C_EP_IN] = *data++;
}
UDP_SET_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXPKTRDY);
while (pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXPKTRDY) {};
while (length) {
// Send next chunk
cpt = MIN(length, AT91C_EP_IN_SIZE);
length -= cpt;
while (cpt--) {
pUdp->UDP_FDR[AT91C_EP_IN] = *data++;
}
// Wait for previous chunk to be sent
// (iceman) when is the bankswapping done?
while (!(pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP)) {
if (!usb_check()) return PM3_EIO;
}
UDP_CLEAR_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXCOMP);
while (pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP) {};
UDP_SET_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXPKTRDY);
while (pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXPKTRDY) {};
}
// Wait for the end of transfer
while (!(pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP)) {
if (!usb_check()) return PM3_EIO;
}
UDP_CLEAR_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXCOMP);
while (pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP) {};
if (len % AT91C_EP_IN_SIZE == 0) {
UDP_SET_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXPKTRDY);
while (!(pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP)) {};
UDP_CLEAR_EP_FLAGS(AT91C_EP_IN, AT91C_UDP_TXCOMP);
while (pUdp->UDP_CSR[AT91C_EP_IN] & AT91C_UDP_TXCOMP) {};
}
return PM3_SUCCESS;
}
/*
*----------------------------------------------------------------------------
* \fn AT91F_USB_SendData
* \brief Send Data through the control endpoint
*----------------------------------------------------------------------------
*/
void AT91F_USB_SendData(AT91PS_UDP pudp, const char *pData, uint32_t length) {
AT91_REG csr;
do {
uint32_t cpt = MIN(length, AT91C_EP_CONTROL_SIZE);
length -= cpt;
while (cpt--)
pudp->UDP_FDR[AT91C_EP_CONTROL] = *pData++;
if (pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP) {
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_TXCOMP);
while (pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP);
}
UDP_SET_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_TXPKTRDY);
do {
csr = pudp->UDP_CSR[AT91C_EP_CONTROL];
// Data IN stage has been stopped by a status OUT
if (csr & AT91C_UDP_RX_DATA_BK0) {
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_RX_DATA_BK0)
return;
}
} while (!(csr & AT91C_UDP_TXCOMP));
} while (length);
if (pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP) {
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_TXCOMP);
while (pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP);
}
}
//*----------------------------------------------------------------------------
//* \fn AT91F_USB_SendZlp
//* \brief Send zero length packet through the control endpoint
//*----------------------------------------------------------------------------
void AT91F_USB_SendZlp(AT91PS_UDP pudp) {
UDP_SET_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_TXPKTRDY);
while (!(pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP)) {};
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_TXCOMP);
while (pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_TXCOMP) {};
}
//*----------------------------------------------------------------------------
//* \fn AT91F_USB_SendStall
//* \brief Stall the control endpoint
//*----------------------------------------------------------------------------
void AT91F_USB_SendStall(AT91PS_UDP pudp) {
UDP_SET_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_FORCESTALL);
while (!(pudp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_ISOERROR)) {};
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, (AT91C_UDP_FORCESTALL | AT91C_UDP_ISOERROR));
while (pudp->UDP_CSR[AT91C_EP_CONTROL] & (AT91C_UDP_FORCESTALL | AT91C_UDP_ISOERROR)) {};
}
//*----------------------------------------------------------------------------
//* \fn AT91F_CDC_Enumerate
//* \brief This function is a callback invoked when a SETUP packet is received
//* problem:
//* 1. this is for USB endpoint0. the control endpoint.
//* 2. mixed with CDC ACM endpoint3 , interrupt, control endpoint
//*----------------------------------------------------------------------------
void AT91F_CDC_Enumerate(void) {
uint8_t bmRequestType, bRequest;
uint16_t wValue, wIndex, wLength, wStatus;
if (!(pUdp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_RXSETUP))
return;
bmRequestType = pUdp->UDP_FDR[AT91C_EP_CONTROL];
bRequest = pUdp->UDP_FDR[AT91C_EP_CONTROL];
wValue = (pUdp->UDP_FDR[AT91C_EP_CONTROL] & 0xFF);
wValue |= (pUdp->UDP_FDR[AT91C_EP_CONTROL] << 8);
wIndex = (pUdp->UDP_FDR[AT91C_EP_CONTROL] & 0xFF);
wIndex |= (pUdp->UDP_FDR[AT91C_EP_CONTROL] << 8);
wLength = (pUdp->UDP_FDR[AT91C_EP_CONTROL] & 0xFF);
wLength |= (pUdp->UDP_FDR[AT91C_EP_CONTROL] << 8);
if (bmRequestType & 0x80) { // Data Phase Transfer Direction Device to Host
UDP_SET_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_DIR);
while (!(pUdp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_DIR)) {};
}
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_RXSETUP);
while ((pUdp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_RXSETUP)) {};
/*
if ( bRequest == MS_VENDOR_CODE) {
if ( bmRequestType == MS_WCID_GET_DESCRIPTOR ) { // C0
if ( wIndex == MS_EXTENDED_COMPAT_ID ) { // 4
//AT91F_USB_SendData(pUdp, CompatIDFeatureDescriptor, MIN(sizeof(CompatIDFeatureDescriptor), wLength));
//return;
}
}
if ( bmRequestType == MS_WCID_GET_FEATURE_DESCRIPTOR ) { //C1
// if ( wIndex == MS_EXTENDED_PROPERTIES ) { // 5 - winusb bug with wIndex == interface index, so I just send it always)
//AT91F_USB_SendData(pUdp, OSprop, MIN(sizeof(OSprop), wLength));
//return;
// }
}
}
*/
// Handle supported standard device request Cf Table 9-3 in USB specification Rev 1.1
switch ((bRequest << 8) | bmRequestType) {
case STD_GET_DESCRIPTOR: {
if (wValue == 0x100) // Return Device Descriptor
AT91F_USB_SendData(pUdp, devDescriptor, MIN(sizeof(devDescriptor), wLength));
else if (wValue == 0x200) // Return Configuration Descriptor
AT91F_USB_SendData(pUdp, cfgDescriptor, MIN(sizeof(cfgDescriptor), wLength));
else if ((wValue & 0xF00) == 0xF00) // Return BOS Descriptor
AT91F_USB_SendData(pUdp, bosDescriptor, MIN(sizeof(bosDescriptor), wLength));
else if ((wValue & 0x300) == 0x300) { // Return String Descriptor
const char *strDescriptor = getStringDescriptor(wValue & 0xff);
if (strDescriptor != NULL) {
AT91F_USB_SendData(pUdp, strDescriptor, MIN(strDescriptor[0], wLength));
} else {
AT91F_USB_SendStall(pUdp);
}
} else {
AT91F_USB_SendStall(pUdp);
}
}
break;
case STD_SET_ADDRESS:
AT91F_USB_SendZlp(pUdp);
pUdp->UDP_FADDR = (AT91C_UDP_FEN | (wValue & 0x7F));
pUdp->UDP_GLBSTATE = (wValue) ? AT91C_UDP_FADDEN : 0;
break;
case STD_SET_CONFIGURATION:
/*
* Set or clear the device "configured" state.
* The LSB of wValue is the "Configuration Number". If this value is non-zero,
* it should be the same number as defined in the Configuration Descriptor;
* otherwise an error must have occurred.
* This device has only one configuration and its Config Number is CONF_NB (= 1).
*/
AT91F_USB_SendZlp(pUdp);
btConfiguration = wValue;
pUdp->UDP_GLBSTATE = (wValue) ? AT91C_UDP_CONFG : AT91C_UDP_FADDEN;
// make sure we are not stalled
/*
UDP_CLEAR_EP_FLAGS(AT91C_EP_OUT , AT91C_UDP_FORCESTALL);
UDP_CLEAR_EP_FLAGS(AT91C_EP_IN , AT91C_UDP_FORCESTALL);
UDP_CLEAR_EP_FLAGS(AT91C_EP_NOTIFY, AT91C_UDP_FORCESTALL);
*/
// enable endpoints
pUdp->UDP_CSR[AT91C_EP_OUT] = (wValue) ? (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_BULK_OUT) : 0;
pUdp->UDP_CSR[AT91C_EP_IN] = (wValue) ? (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_BULK_IN) : 0;
pUdp->UDP_CSR[AT91C_EP_NOTIFY] = (wValue) ? (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_INT_IN) : 0;
break;
case STD_GET_CONFIGURATION:
AT91F_USB_SendData(pUdp, (char *) & (btConfiguration), sizeof(btConfiguration));
break;
case STD_GET_STATUS_ZERO:
wStatus = 0; // Device is Bus powered, remote wakeup disabled
AT91F_USB_SendData(pUdp, (char *) &wStatus, sizeof(wStatus));
break;
case STD_GET_STATUS_INTERFACE:
wStatus = 0; // reserved for future use
AT91F_USB_SendData(pUdp, (char *) &wStatus, sizeof(wStatus));
break;
case STD_GET_STATUS_ENDPOINT:
wStatus = 0;
wIndex &= 0x0F;
if ((pUdp->UDP_GLBSTATE & AT91C_UDP_CONFG) && (wIndex <= AT91C_EP_NOTIFY)) {
wStatus = (pUdp->UDP_CSR[wIndex] & AT91C_UDP_EPEDS) ? 0 : 1;
AT91F_USB_SendData(pUdp, (char *) &wStatus, sizeof(wStatus));
} else if ((pUdp->UDP_GLBSTATE & AT91C_UDP_FADDEN) && (wIndex == AT91C_EP_CONTROL)) {
wStatus = (pUdp->UDP_CSR[wIndex] & AT91C_UDP_EPEDS) ? 0 : 1;
AT91F_USB_SendData(pUdp, (char *) &wStatus, sizeof(wStatus));
} else {
AT91F_USB_SendStall(pUdp);
}
break;
case STD_SET_FEATURE_ZERO:
AT91F_USB_SendStall(pUdp);
break;
case STD_SET_FEATURE_INTERFACE:
AT91F_USB_SendZlp(pUdp);
break;
case STD_SET_FEATURE_ENDPOINT:
wIndex &= 0x0F;
if ((wValue == 0) && (wIndex >= AT91C_EP_OUT) && (wIndex <= AT91C_EP_NOTIFY)) {
pUdp->UDP_CSR[wIndex] = 0;
AT91F_USB_SendZlp(pUdp);
} else {
AT91F_USB_SendStall(pUdp);
}
break;
case STD_CLEAR_FEATURE_ZERO:
AT91F_USB_SendStall(pUdp);
break;
case STD_CLEAR_FEATURE_INTERFACE:
AT91F_USB_SendZlp(pUdp);
break;
case STD_CLEAR_FEATURE_ENDPOINT:
wIndex &= 0x0F;
if ((wValue == 0) && (wIndex >= AT91C_EP_OUT) && (wIndex <= AT91C_EP_NOTIFY)) {
if (wIndex == AT91C_EP_OUT) pUdp->UDP_CSR[AT91C_EP_OUT] = (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_BULK_OUT);
else if (wIndex == AT91C_EP_IN) pUdp->UDP_CSR[AT91C_EP_IN] = (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_BULK_IN);
else if (wIndex == AT91C_EP_NOTIFY) pUdp->UDP_CSR[AT91C_EP_NOTIFY] = (AT91C_UDP_EPEDS | AT91C_UDP_EPTYPE_INT_IN);
AT91F_USB_SendZlp(pUdp);
} else {
AT91F_USB_SendStall(pUdp);
}
break;
// handle CDC class requests
case SET_LINE_CODING: {
/*
uint8_t i;
for ( i = 0 ; i < 7 ; i++ ) {
((uint8_t*)&line)[i] = pUdp->UDP_FDR[AT91C_EP_CONTROL];
} */
// ignore SET_LINE_CODING...
while (!(pUdp->UDP_CSR[AT91C_EP_CONTROL] & AT91C_UDP_RX_DATA_BK0)) {};
UDP_CLEAR_EP_FLAGS(AT91C_EP_CONTROL, AT91C_UDP_RX_DATA_BK0);
AT91F_USB_SendZlp(pUdp);
break;
}
case GET_LINE_CODING:
AT91F_USB_SendData(pUdp, (char *) &line, MIN(sizeof(line), wLength));
break;
case SET_CONTROL_LINE_STATE:
btConnection = wValue;
AT91F_USB_SendZlp(pUdp);
break;
default:
AT91F_USB_SendStall(pUdp);
break;
}
}
Reference in a new issue View git blame Copy permalink