mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2024-09-20 23:36:31 +08:00
372 lines
9.1 KiB
C
372 lines
9.1 KiB
C
#include "flashmem.h"
|
||
|
||
/* here: use NCPS2 @ PA10: */
|
||
#define SPI_CSR_NUM 2 // Chip Select register[] 0,1,2,3 (at91samv512 has 4)
|
||
|
||
/* PCS_0 for NPCS0, PCS_1 for NPCS1 ... */
|
||
#define PCS_0 ((0<<0)|(1<<1)|(1<<2)|(1<<3)) // 0xE - 1110
|
||
#define PCS_1 ((1<<0)|(0<<1)|(1<<2)|(1<<3)) // 0xD - 1101
|
||
#define PCS_2 ((1<<0)|(1<<1)|(0<<2)|(1<<3)) // 0xB - 1011
|
||
#define PCS_3 ((1<<0)|(1<<1)|(1<<2)|(0<<3)) // 0x7 - 0111
|
||
|
||
// TODO
|
||
#if (SPI_CSR_NUM == 0)
|
||
#define SPI_MR_PCS PCS_0
|
||
#elif (SPI_CSR_NUM == 1)
|
||
#define SPI_MR_PCS PCS_1
|
||
#elif (SPI_CSR_NUM == 2)
|
||
#define SPI_MR_PCS PCS_2
|
||
#elif (SPI_CSR_NUM == 3)
|
||
#define SPI_MR_PCS PCS_3
|
||
#else
|
||
#error "SPI_CSR_NUM invalid"
|
||
// not realy - when using an external address decoder...
|
||
// but this code takes over the complete SPI-interace anyway
|
||
#endif
|
||
|
||
|
||
/*
|
||
读取指令，可以从一个位置开始持续的读，最多能将整块芯片读取完
|
||
页写指令，每次写入为1-256字节，但是不能跨越256字节边界
|
||
擦除指令，擦除指令后必须将CS拉高，否则不会执行
|
||
*/
|
||
|
||
void FlashSetup(void) {
|
||
// PA1 -> SPI_NCS3 chip select (MEM)
|
||
// PA10 -> SPI_NCS2 chip select (LCD)
|
||
// PA11 -> SPI_NCS0 chip select (FPGA)
|
||
// PA12 -> SPI_MISO Master-In Slave-Out
|
||
// PA13 -> SPI_MOSI Master-Out Slave-In
|
||
// PA14 -> SPI_SPCK Serial Clock
|
||
|
||
// Disable PIO control of the following pins, allows use by the SPI peripheral
|
||
AT91C_BASE_PIOA->PIO_PDR = GPIO_NCS0 | GPIO_MISO | GPIO_MOSI | GPIO_SPCK | GPIO_NCS2;
|
||
|
||
// Pull-up Enable
|
||
AT91C_BASE_PIOA->PIO_PPUER = GPIO_NCS0 | GPIO_MISO | GPIO_MOSI | GPIO_SPCK | GPIO_NCS2;
|
||
|
||
// Peripheral A
|
||
AT91C_BASE_PIOA->PIO_ASR = GPIO_NCS0 | GPIO_MISO | GPIO_MOSI | GPIO_SPCK;
|
||
|
||
// Peripheral B
|
||
AT91C_BASE_PIOA->PIO_BSR |= GPIO_NCS2;
|
||
|
||
//enable the SPI Peripheral clock
|
||
AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_SPI);
|
||
|
||
// Enable SPI
|
||
AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIEN;
|
||
|
||
// NPCS2 Mode 0
|
||
AT91C_BASE_SPI->SPI_MR =
|
||
( 0 << 24) | // Delay between chip selects (take default: 6 MCK periods)
|
||
(0xB << 16) | // Peripheral Chip Select (selects SPI_NCS2 or PA10)
|
||
( 0 << 7) | // Local Loopback Disabled
|
||
( 1 << 4) | // Mode Fault Detection disabled
|
||
( 0 << 2) | // Chip selects connected directly to peripheral
|
||
( 0 << 1) | // Fixed Peripheral Select
|
||
( 1 << 0); // Master Mode
|
||
|
||
// 8 bit
|
||
AT91C_BASE_SPI->SPI_CSR[2] =
|
||
( 0 << 24) | // Delay between Consecutive Transfers (32 MCK periods)
|
||
( 0 << 16) | // Delay Before SPCK (1 MCK period)
|
||
( 6 << 8) | // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud
|
||
( 0 << 4) | // Bits per Transfer (8 bits)
|
||
( 1 << 3) | // Chip Select inactive after transfer
|
||
( 1 << 1) | // Clock Phase data captured on leading edge, changes on following edge
|
||
( 0 << 0); // Clock Polarity inactive state is logic 0
|
||
|
||
// read first, empty buffer
|
||
if (AT91C_BASE_SPI->SPI_RDR == 0) {};
|
||
}
|
||
|
||
void FlashStop(void) {
|
||
//* Reset all the Chip Select register
|
||
AT91C_BASE_SPI->SPI_CSR[0] = 0;
|
||
AT91C_BASE_SPI->SPI_CSR[1] = 0;
|
||
AT91C_BASE_SPI->SPI_CSR[2] = 0;
|
||
AT91C_BASE_SPI->SPI_CSR[3] = 0;
|
||
|
||
// Reset the SPI mode
|
||
AT91C_BASE_SPI->SPI_MR = 0;
|
||
|
||
// Disable all interrupts
|
||
AT91C_BASE_SPI->SPI_IDR = 0xFFFFFFFF;
|
||
|
||
// SPI disable
|
||
AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIDIS;
|
||
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("FlashStop");
|
||
|
||
StopTicks();
|
||
}
|
||
|
||
// send one byte over SPI
|
||
uint16_t FlashSendByte(uint32_t data) {
|
||
uint16_t incoming = 0;
|
||
|
||
WDT_HIT();
|
||
|
||
// wait until SPI is ready for transfer
|
||
while ((AT91C_BASE_SPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0) {};
|
||
|
||
// send the data
|
||
AT91C_BASE_SPI->SPI_TDR = data;
|
||
|
||
// wait recive transfer is complete
|
||
while ((AT91C_BASE_SPI->SPI_SR & AT91C_SPI_RDRF) == 0)
|
||
WDT_HIT();
|
||
|
||
// reading incoming data
|
||
incoming = ((AT91C_BASE_SPI->SPI_RDR) & 0xFFFF);
|
||
|
||
return incoming;
|
||
}
|
||
|
||
// send last byte over SPI
|
||
uint16_t FlashSendLastByte(uint32_t data) {
|
||
return FlashSendByte(data | AT91C_SPI_LASTXFER);
|
||
}
|
||
|
||
// read state register 1
|
||
uint8_t Flash_ReadStat1(void) {
|
||
FlashSendByte(READSTAT1);
|
||
uint8_t stat1 = FlashSendLastByte(0xFF);
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("stat1 [%02x]", stat1);
|
||
return stat1;
|
||
}
|
||
|
||
// read state register 2
|
||
uint8_t Flash_ReadStat2(void) {
|
||
FlashSendByte(READSTAT2);
|
||
uint8_t stat2 = FlashSendLastByte(0xFF);
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("stat2 [%02x]", stat2);
|
||
return stat2;
|
||
}
|
||
|
||
// determine whether FLASHMEM is busy
|
||
bool Flash_CheckBusy(uint16_t times){
|
||
bool ret = (Flash_ReadStat1() & BUSY);
|
||
|
||
if (!ret || !times || !(times--))
|
||
return ret;
|
||
|
||
while (times) {
|
||
WDT_HIT();
|
||
WaitMS(1);
|
||
ret = (Flash_ReadStat1() & BUSY);
|
||
if (!ret)
|
||
break;
|
||
times--;
|
||
}
|
||
return ret;
|
||
}
|
||
|
||
// read ID out
|
||
uint8_t Flash_ReadID(void) {
|
||
|
||
if (Flash_CheckBusy(1000)) return 0;
|
||
|
||
// Manufacture ID / device ID
|
||
FlashSendByte(ID);
|
||
FlashSendByte(0x00);
|
||
FlashSendByte(0x00);
|
||
FlashSendByte(0x00);
|
||
|
||
uint8_t man_id = FlashSendByte(0xFF);
|
||
uint8_t dev_id = FlashSendLastByte(0xFF);
|
||
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("Flash ReadID | Man ID %02x | Device ID %02x", man_id, dev_id);
|
||
|
||
if ( (man_id == WINBOND_MANID ) && (dev_id == WINBOND_DEVID) )
|
||
return dev_id;
|
||
|
||
return 0;
|
||
}
|
||
|
||
// read unique id for chip.
|
||
void Flash_UniqueID(uint8_t *uid) {
|
||
|
||
if (Flash_CheckBusy(1000)) return;
|
||
|
||
// reading unique serial number
|
||
FlashSendByte(UNIQUE_ID);
|
||
FlashSendByte(0x00);
|
||
FlashSendByte(0x00);
|
||
FlashSendByte(0x00);
|
||
FlashSendByte(0x00);
|
||
|
||
uid[3] = FlashSendByte(0xFF);
|
||
uid[2] = FlashSendByte(0xFF);
|
||
uid[1] = FlashSendByte(0xFF);
|
||
uid[0] = FlashSendLastByte(0xFF);
|
||
}
|
||
|
||
uint8_t Flash_ReadData(uint32_t address, uint8_t *out, uint16_t len) {
|
||
// length should never be zero
|
||
if (!len || Flash_CheckBusy(1000)) return 0;
|
||
|
||
FlashSendByte(READDATA);
|
||
FlashSendByte((address >> 16) & 0xFF);
|
||
FlashSendByte((address >> 8) & 0xFF);
|
||
FlashSendByte((address >> 0) & 0xFF);
|
||
|
||
uint16_t i = 0;
|
||
for (; i < (len - 1); i++)
|
||
out[i] = FlashSendByte(0xFF);
|
||
|
||
out[i] = FlashSendLastByte(0xFF);
|
||
return len;
|
||
}
|
||
|
||
// Write data
|
||
uint8_t Flash_WriteData(uint32_t address, uint8_t *in, uint16_t len) {
|
||
// length should never be zero
|
||
if (!len || Flash_CheckBusy(1000)) return 0;
|
||
|
||
// 不能跨越 256 字节边界
|
||
if (((address & 255) + len) > 256) return 0;
|
||
|
||
FlashSendByte(PAGEPROG);
|
||
FlashSendByte((address >> 16) & 0xFF);
|
||
FlashSendByte((address >> 8) & 0xFF);
|
||
FlashSendByte((address >> 0) & 0xFF);
|
||
|
||
uint16_t i = 0;
|
||
for (; i < (len - 1); i++)
|
||
FlashSendByte(in[i]);
|
||
|
||
FlashSendLastByte(in[i]);
|
||
return len;
|
||
}
|
||
|
||
// enable the flash write
|
||
void Flash_WriteEnable() {
|
||
FlashSendLastByte(WRITEENABLE);
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("Flash Write enabled");
|
||
}
|
||
|
||
// erase 4K at one time
|
||
bool Flash_Erase4k(uint32_t address) {
|
||
if (address & (4096 - 1)) {
|
||
if ( MF_DBGLEVEL > 1 ) Dbprintf("Flash_Erase4k : Address is not align at 4096");
|
||
return false;
|
||
}
|
||
|
||
FlashSendByte(SECTORERASE);
|
||
FlashSendByte((address >> 16) & 0xFF);
|
||
FlashSendByte((address >> 8) & 0xFF);
|
||
FlashSendLastByte((address >> 0) & 0xFF);
|
||
return true;
|
||
}
|
||
|
||
// erase 32K at one time
|
||
bool Flash_Erase32k(uint32_t address) {
|
||
if (address & (32*1024 - 1)) {
|
||
if ( MF_DBGLEVEL > 1 ) Dbprintf("Flash_Erase4k : Address is not align at 4096");
|
||
return false;
|
||
}
|
||
FlashSendByte(BLOCK32ERASE);
|
||
FlashSendByte((address >> 16) & 0xFF);
|
||
FlashSendByte((address >> 8) & 0xFF);
|
||
FlashSendLastByte((address >> 0) & 0xFF);
|
||
return true;
|
||
}
|
||
|
||
// erase 64k at one time
|
||
bool Flash_Erase64k(uint32_t address) {
|
||
|
||
if (address & (64*1024 - 1)) {
|
||
if ( MF_DBGLEVEL > 1 ) Dbprintf("Flash_Erase4k : Address is not align at 4096");
|
||
return false;
|
||
}
|
||
FlashSendByte(BLOCK64ERASE);
|
||
FlashSendByte((address >> 16) & 0xFF);
|
||
FlashSendByte((address >> 8) & 0xFF);
|
||
FlashSendLastByte((address >> 0) & 0xFF);
|
||
return true;
|
||
}
|
||
|
||
// Erase chip
|
||
void Flash_EraseChip(void) {
|
||
FlashSendLastByte(CHIPERASE);
|
||
}
|
||
|
||
// initialize
|
||
bool FlashInit(void) {
|
||
FlashSetup();
|
||
|
||
StartTicks();
|
||
|
||
if (Flash_CheckBusy(1000)) {
|
||
StopTicks();
|
||
return false;
|
||
}
|
||
|
||
if ( MF_DBGLEVEL > 3 ) Dbprintf("FlashInit OK");
|
||
return true;
|
||
}
|
||
|
||
void EXFLASH_TEST(void) {
|
||
uint8_t data[256] = { 0x00, 0x01, 0x02 };
|
||
uint8_t data2[256] = { 0x00};
|
||
|
||
if (!FlashInit()) return;
|
||
|
||
Flash_ReadStat1();
|
||
|
||
Dbprintf("Flash test write: 012 to 0x00 0x01 0x02");
|
||
Flash_WriteEnable();
|
||
Flash_Erase4k(0x00);
|
||
if (Flash_CheckBusy(1000)) {
|
||
Dbprintf("Flash_Erase4k CheckBusy Error.");
|
||
return;
|
||
}
|
||
|
||
Flash_ReadData(0, data2, 256);
|
||
Flash_WriteEnable();
|
||
Flash_WriteData(0x12, data, sizeof(data)); // this will never run, cuz out of 256byte boundary
|
||
Flash_WriteData(0x12, data, 3);
|
||
|
||
if (Flash_CheckBusy(1000)) {
|
||
Dbprintf("Flash_WriteDate CheckBusy Error.");
|
||
return;
|
||
}
|
||
|
||
Flash_ReadData(0, data2, 256);
|
||
FlashStop();
|
||
}
|
||
|
||
|
||
void Flashmem_print_status(void) {
|
||
DbpString("Flash memory");
|
||
|
||
if (!FlashInit()) {
|
||
DbpString(" init....................FAIL");
|
||
return;
|
||
}
|
||
DbpString(" init....................OK");
|
||
|
||
uint8_t dev_id = Flash_ReadID();
|
||
switch (dev_id) {
|
||
case 0x11 :
|
||
DbpString(" Memory size.............2 mbits / 256kb");
|
||
break;
|
||
case 0x10 :
|
||
DbpString(" Memory size..... .......1 mbits / 128kb");
|
||
break;
|
||
case 0x05 :
|
||
DbpString(" Memory size.............512 kbits / 64kb");
|
||
break;
|
||
default :
|
||
DbpString(" Device ID............... --> Unknown <--");
|
||
break;
|
||
}
|
||
|
||
uint8_t uid[4] = {0,0,0,0};
|
||
Flash_UniqueID(uid);
|
||
Dbprintf(" Unique ID...............0x%02x%02x%02x%02x %", uid[3], uid[2], uid[1], uid[0]);
|
||
|
||
FlashStop();
|
||
} |