mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2024-11-20 08:32:24 +08:00
77 lines
2.7 KiB
Verilog
77 lines
2.7 KiB
Verilog
//-----------------------------------------------------------------------------
|
|
// Copyright (C) 2014 iZsh <izsh at fail0verflow.com>
|
|
//
|
|
// This code is licensed to you under the terms of the GNU GPL, version 2 or,
|
|
// at your option, any later version. See the LICENSE.txt file for the text of
|
|
// the license.
|
|
//-----------------------------------------------------------------------------
|
|
// input clk is 24MHz
|
|
`include "min_max_tracker.v"
|
|
|
|
module lf_edge_detect(input clk, input [7:0] adc_d, input [7:0] lf_ed_threshold,
|
|
output [7:0] max, output [7:0] min,
|
|
output [7:0] high_threshold, output [7:0] highz_threshold,
|
|
output [7:0] lowz_threshold, output [7:0] low_threshold,
|
|
output edge_state, output edge_toggle);
|
|
|
|
min_max_tracker tracker(clk, adc_d, lf_ed_threshold, min, max);
|
|
|
|
// auto-tune
|
|
assign high_threshold = (max + min) / 2 + (max - min) / 4;
|
|
assign highz_threshold = (max + min) / 2 + (max - min) / 8;
|
|
assign lowz_threshold = (max + min) / 2 - (max - min) / 8;
|
|
assign low_threshold = (max + min) / 2 - (max - min) / 4;
|
|
|
|
// heuristic to see if it makes sense to try to detect an edge
|
|
wire enabled =
|
|
(high_threshold > highz_threshold)
|
|
& (highz_threshold > lowz_threshold)
|
|
& (lowz_threshold > low_threshold)
|
|
& ((high_threshold - highz_threshold) > 8)
|
|
& ((highz_threshold - lowz_threshold) > 16)
|
|
& ((lowz_threshold - low_threshold) > 8);
|
|
|
|
// Toggle the output with hysteresis
|
|
// Set to high if the ADC value is above the threshold
|
|
// Set to low if the ADC value is below the threshold
|
|
reg is_high = 0;
|
|
reg is_low = 0;
|
|
reg is_zero = 0;
|
|
reg trigger_enabled = 1;
|
|
reg output_edge = 0;
|
|
reg output_state;
|
|
|
|
always @(posedge clk)
|
|
begin
|
|
is_high <= (adc_d >= high_threshold);
|
|
is_low <= (adc_d <= low_threshold);
|
|
is_zero <= ((adc_d > lowz_threshold) & (adc_d < highz_threshold));
|
|
end
|
|
|
|
// all edges detection
|
|
always @(posedge clk)
|
|
if (enabled) begin
|
|
// To enable detecting two consecutive peaks at the same level
|
|
// (low or high) we check whether or not we went back near 0 in-between.
|
|
// This extra check is necessary to prevent from noise artifacts
|
|
// around the threshold values.
|
|
if (trigger_enabled & (is_high | is_low)) begin
|
|
output_edge <= ~output_edge;
|
|
trigger_enabled <= 0;
|
|
end else
|
|
trigger_enabled <= trigger_enabled | is_zero;
|
|
end
|
|
|
|
// edge states
|
|
always @(posedge clk)
|
|
if (enabled) begin
|
|
if (is_high)
|
|
output_state <= 1'd1;
|
|
else if (is_low)
|
|
output_state <= 1'd0;
|
|
end
|
|
|
|
assign edge_state = output_state;
|
|
assign edge_toggle = output_edge;
|
|
|
|
endmodule
|