mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2024-11-20 08:32:24 +08:00
91 lines
2.7 KiB
Verilog
91 lines
2.7 KiB
Verilog
//-----------------------------------------------------------------------------
|
|
// The way that we connect things in low-frequency simulation mode. In this
|
|
// case just pass everything through to the ARM, which can bit-bang this
|
|
// (because it is so slow).
|
|
//
|
|
// Jonathan Westhues, April 2006
|
|
//-----------------------------------------------------------------------------
|
|
|
|
module lo_adc(
|
|
pck0,
|
|
pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
|
|
adc_d, adc_clk,
|
|
ssp_frame, ssp_din, ssp_dout, ssp_clk,
|
|
dbg, divisor,
|
|
lf_field
|
|
);
|
|
input pck0;
|
|
output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
|
|
input [7:0] adc_d;
|
|
output adc_clk;
|
|
input ssp_dout;
|
|
output ssp_frame, ssp_din, ssp_clk;
|
|
output dbg;
|
|
input [7:0] divisor;
|
|
input lf_field;
|
|
|
|
reg [7:0] to_arm_shiftreg;
|
|
reg [7:0] pck_divider;
|
|
reg clk_state;
|
|
|
|
// Antenna logic, depending on "lf_field" (in arm defined as FPGA_LF_READER_FIELD)
|
|
wire tag_modulation = ssp_dout & !lf_field;
|
|
wire reader_modulation = !ssp_dout & lf_field & clk_state;
|
|
|
|
// always on (High Frequency outputs, unused)
|
|
assign pwr_oe1 = 1'b0;
|
|
assign pwr_hi = 1'b0;
|
|
|
|
// low frequency outputs
|
|
assign pwr_lo = reader_modulation;
|
|
assign pwr_oe2 = 1'b0; // 33 Ohms
|
|
assign pwr_oe3 = tag_modulation; // base antenna load = 33 Ohms
|
|
assign pwr_oe4 = 1'b0; // 10k Ohms
|
|
|
|
// Debug Output ADC clock
|
|
assign dbg = adc_clk;
|
|
|
|
// ADC clock out of phase with antenna driver
|
|
assign adc_clk = ~clk_state;
|
|
|
|
// serialized SSP data is gated by clk_state to suppress unwanted signal
|
|
assign ssp_din = to_arm_shiftreg[7] && !clk_state;
|
|
|
|
// SSP clock always runs at 24MHz
|
|
assign ssp_clk = pck0;
|
|
|
|
// SSP frame is gated by clk_state and goes high when pck_divider=8..15
|
|
assign ssp_frame = (pck_divider[7:3] == 5'd1) && !clk_state;
|
|
|
|
// divide 24mhz down to 3mhz
|
|
always @(posedge pck0)
|
|
begin
|
|
if (pck_divider == divisor[7:0])
|
|
begin
|
|
pck_divider <= 8'd0;
|
|
clk_state = !clk_state;
|
|
end
|
|
else
|
|
begin
|
|
pck_divider <= pck_divider + 1;
|
|
end
|
|
end
|
|
|
|
// this task also runs at pck0 frequency (24Mhz) and is used to serialize
|
|
// the ADC output which is then clocked into the ARM SSP.
|
|
always @(posedge pck0)
|
|
begin
|
|
if ((pck_divider == 8'd7) && !clk_state)
|
|
to_arm_shiftreg <= adc_d;
|
|
else begin
|
|
to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
|
|
// simulation showed a glitch occuring due to the LSB of the shifter
|
|
// not being set as we shift bits out
|
|
// this ensures the ssp_din remains low after a transfer and suppresses
|
|
// the glitch that would occur when the last data shifted out ended in
|
|
// a 1 bit and the next data shifted out started with a 0 bit
|
|
to_arm_shiftreg[0] <= 1'b0;
|
|
end
|
|
end
|
|
|
|
endmodule
|