Proxmark3 RDV40 dedicated repo, based on iceman fork

Notice

This repo is based on iceman fork for proxmark3. It is dedicated to bring the most out of the new features for proxmark3 RDV40 device.

Donations

Nothing says thank you as much as a donation, https://www.patreon.com/iceman1001

ToC

• Coverity Scan Config & Run

• Whats changed?

• Why didn't you based it on offical PM3 Master?

• Why don't you add this or that functionality?

• PM3 GUI

• Development

• KALI and ARCHLINUX users

• Setup and build for UBUNTU

• Setup and build for ArchLinux

• Homebrew (Mac OS X)

• Upgrading HomeBrew tap formula

• Building on Windows

• Gator96100 distro

• Build and run

• Validating proxmark client functionality

• Run the following commands

• Quit client

• First things on your RDV40

• Verify sim module firmware version

• The end

Coverity Scan Config & Run

Download the Coverity Scan Self-buld and install it. You will need to configure ARM-NON-EABI- Compiler for it to use:

• Configure

cov-configure --comptype gcc --compiler /opt/devkitpro/devkitARM/bin/arm-none-eabi-gcc

• Run it (I'm running on Ubuntu)

cov-build --dir cov-int make all

• Make a tarball

tar czvf proxmark3.tgz cov-int

• Upload it to coverity.com

Whats changed?

* added flash memory 256kb.
* added smart card module
* added FPC connector

---

Why didn't you based it on offical PM3 Master?

The separation from offical pm3 repo gives us very much freedom to create a firmware/client that suits the RDV40 features. We don't want to mess up the offical pm3 repo with RDV40 specific code.

Why don't you add this or that functionality?

Give us a hint, and we'll see if we can't merge in the stuff you have.

PM3 GUI

The official PM3-GUI from Gaucho will not work. The new universial GUI will work. Proxmark3 Univerisal GUI

Development

This fork now compiles just fine on

• Windows/mingw environment with Qt5.6.1 & GCC 4.8
• Ubuntu 1404, 1510, 1604, 1804
• Mac OS X / Homebrew
• ParrotOS
• WSL (Windows subsystem linux) on Windows 10
• Docker container

KALI and ARCHLINUX users

Kali and ArchLinux users usually must kill their modem manager in order for the proxmark3 to enumerate properly.

sudo apt remove modemmanager

or

systemctl stop ModemManager
systemctl disable ModemManager

Setup and build for UBUNTU

GC made updates to allow this to build easily on Ubuntu 14.04.2 LTS, 15.10 or 16.04 See https://github.com/Proxmark/proxmark3/wiki/Ubuntu%20Linux

A nice and cool install script made by @daveio is found here: https://github.com/daveio/attacksurface/blob/master/proxmark3/pm3-setup.sh I have also added this script to the fork. https://github.com/RfidResearchGroup/proxmark3/blob/master/install.sh

• Run sudo apt-get install p7zip git build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config wget libncurses5-dev gcc-arm-none-eabi

• Clone fork git clone https://github.com/RfidResearchGroup/proxmark3.git

• Get the latest commits git pull

• Install the blacklist rules and add user to dialout group (if you on a Linux/ubuntu/debian). If you do this one, you need to logout and login in again to make sure your rights got changed. make udev

• Clean and complete compilation make clean && make all

• Flash the BOOTROM & FULLIMAGE client/flasher /dev/ttyACM0 -b bootrom/obj/bootrom.elf armsrc/obj/fullimage.elf

• Change into the client folder cd client

• Run the client ./proxmark3 /dev/ttyACM0

Setup and build for ArchLinux

• Run sudo pacman -Sy base-devel p7zip libusb readline ncurses arm-none-eabi-newlib --needed yaourt -S termcap

• Remove modemmanager sudo apt remove modemmanager

• Clone fork git clone https://github.com/RfidResearchGroup/proxmark3.git

• Get the latest commits git pull

• Install the blacklist rules and add user to dialout group (if you on a Linux/ubuntu/debian). If you do this one, you need to logout and login in again to make sure your rights got changed. make udev

• Clean and complete compilation make clean && make all

• Flash the BOOTROM & FULLIMAGE client/flasher /dev/ttyACM0 -b bootrom/obj/bootrom.elf armsrc/obj/fullimage.elf

• Change into the client folder cd client

• Run the client ./proxmark3 /dev/ttyACM0

Homebrew (Mac OS X)

These instructions comes from @Chrisfu, where I got the proxmark3.rb scriptfile from. Further questions about Mac & Homebrew, contact @Chrisfu (https://github.com/chrisfu/)

1. Install homebrew if you haven't yet already done so: http://brew.sh/

2. Tap this repo: brew tap RfidResearchGroup/proxmark3

3. Install Proxmark3: brew install proxmark3 for stable release or brew install --HEAD proxmark3 for latest non-stable from GitHub.

Upgrading HomeBrew tap formula

This method is useful for those looking to run bleeding-edge versions of iceman's client. Keep this in mind when attempting to update your HomeBrew tap formula as this procedure could easily cause a build to break if an update is unstable on macOS.

Tested on macOS High Sierra 10.13.2

Note: This assumes you have already installed iceman's fork from HomeBrew as mentioned above

1. Force HomeBrew to pull the latest source from github brew upgrade --fetch-HEAD RfidResearchGroup/proxmark3

2. Flash the bootloader & fullimage.elf

• With your Proxmark3 unplugged from your machine, press and hold the button on your Proxmark 3 as you plug it into a USB port. Continue to hold the button until after this step is complete and the proxmark3-flasher command outputs "Have a nice day!"* $ sudo proxmark3-flasher /dev/tty.usbmodem881 -b /usr/local/Cellar/proxmark3/HEAD-6a710ef/share/firmware/bootrom.elf /usr/local/Cellar/proxmark3/HEAD-6a710ef/share/firmware/fullimage.elf

$ sudo proxmark3-flasher /dev/tty.usbmodem881

4. Enjoy the update

Building on Windows

Gator96100 distro

Rather than download and install every one of these packages, a new ProxSpace environment archive file will be made available for download on the project page at @Gator96100's repo

Afterwards just clone the iceman repo or download someone elses. Read instructions on @Gator96100 repo page. (https://github.com/Gator96100/ProxSpace/)

Links

• https://github.com/Gator96100/ProxSpace/releases/tag/v3.1 (release v3.1 with gcc v7.3.0 )
• https://github.com/Gator96100/ProxSpace/releases/tag/v2.2 (release v2.2 with gcc v5.3.0 arm-none-eabi-gcc v7.1.0)

Build and run

• Clone fork git clone https://github.com/RfidResearchGroup/proxmark3.git

• Get the latest commits git pull

• CLEAN COMPILE make clean && make all

Assuming you have Proxmark3 Windows drivers installed you can run the Proxmark software where "X" is the com port number assigned to proxmark3 under Windows.

• Flash the BOOTROM & FULLIMAGE client/flasher.exe comX -b bootrom/obj/bootrom.elf armsrc/obj/fullimage.elf

• Change into the client folder cd client

• Run the client proxmark3.exe comX

Validating proxmark client functionality

If all went well you should get some information about the firmware and memory usage as well as the prompt, something like this.

[=] UART Setting serial baudrate 460800

Proxmark3 RFID instrument

[ CLIENT ]

client: iceman build for RDV40 with flashmem; smartcard;

[ ARM ]

bootrom: iceman/master/4517531c-dirty-unclean 2018-12-13 15:42:24

os: iceman/master/5a34550a-dirty-unclean 2019-01-07 23:04:07

[ FPGA ]

LF image built for 2s30vq100 on 2018/ 9/ 8 at 13:57:51

HF image built for 2s30vq100 on 2018/ 9/ 3 at 21:40:23

[ Hardware ]

--= uC: AT91SAM7S512 Rev B

--= Embedded Processor: ARM7TDMI

--= Nonvolatile Program Memory Size: 512K bytes, Used: 247065 bytes (47%) Free: 277223 bytes (53%)

--= Second Nonvolatile Program Memory Size: None

--= Internal SRAM Size: 64K bytes

--= Architecture Identifier: AT91SAM7Sxx Series

--= Nonvolatile Program Memory Type: Embedded Flash Memory

pm3 -->

Run the following commands

pm3 --> hw status
pm3 --> hw version
pm3 --> hw tune

You are now ready to use your newly upgraded proxmark3 device. Many commands uses the h parameter to show a help text. The client uses a arcaic command structure which will be hard to grasp at first. Here are some commands to start off with.

pm3 --> hf
pm3 --> hf 14a info
pm3 --> lf
pm3 --> lf search

Quit client

pm3 --> quit

First things on your RDV40

You will need to run these commands to make sure your rdv4 is prepared

pm3 --> mem load f default_keys m
pm3 --> mem load f default_pwd t
pm3 --> mem load f default_iclass_keys i
pm3 --> lf t55xx deviceconfig a 29 b 17 c 15 d 47 e 15 p

Verify sim module firmware version

To make sure you got the latest sim module firmware. Lastest version is v3.11

pm3 --> hw status

Find version in the long output, look for these two lines

#db# Smart card module (ISO 7816)
#db#   version.................v2.06

This version is obselete. The following command upgrades your device sim module firmware. Don't not turn of your device during the execution of this command.

pm3 --> sc upgrade f ../tools/simmodule/SIM011.BIN 

You get the following output, this is a successful execution.

[!] WARNING - Smartcard socket firmware upgrade.          
[!] A dangerous command, do wrong and you will brick the smart card socket          
[+] Smartcard socket firmware uploading to PM3          
..
[+] Smartcard socket firmware updating,  don't turn off your PM3!          
#db# FW 0000          
#db# FW 0080          
#db# FW 0100          
#db# FW 0180          
#db# FW 0200          
#db# FW 0280          
[+] Smartcard socket firmware upgraded successful        

the end

iceman at host iuse.se July 2018, Sweden