mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2024-12-27 10:34:08 +08:00
b014c96d68
fpga/lo_read.v (lf_field): new argument. fpga/fpga_lf.v: modify accordingly. armsrc/apps.h (FPGA_MAJOR_MODE_LF_READER): Rename as FPGA_MAJOR_MODE_LF_ADC. armsrc/apps.h (FPGA_LF_ADC_READER_FIELD): New LF option. armsrc/lfops.c: Modify accordingly. client/cmdlf.c (CmdLFSnoop): New command. armsrc/appmain.c, armsrc/lfops.c, client/cmdlf.h, include/usb_cmd.h: Modify accordingly.
74 lines
2.8 KiB
Verilog
74 lines
2.8 KiB
Verilog
//-----------------------------------------------------------------------------
|
|
// The way that we connect things in low-frequency read mode. In this case
|
|
// we are generating the unmodulated low frequency carrier.
|
|
// The A/D samples at that same rate and the result is serialized.
|
|
//
|
|
// Jonathan Westhues, April 2006
|
|
// iZsh <izsh at fail0verflow.com>, June 2014
|
|
//-----------------------------------------------------------------------------
|
|
|
|
module lo_read(
|
|
input pck0, input [7:0] pck_cnt, input pck_divclk,
|
|
output pwr_lo, output pwr_hi,
|
|
output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
|
|
input [7:0] adc_d, output adc_clk,
|
|
output ssp_frame, output ssp_din, output ssp_clk,
|
|
output dbg,
|
|
input lf_field
|
|
);
|
|
|
|
reg [7:0] to_arm_shiftreg;
|
|
|
|
// this task also runs at pck0 frequency (24Mhz) and is used to serialize
|
|
// the ADC output which is then clocked into the ARM SSP.
|
|
|
|
// because pck_divclk always transitions when pck_cnt = 0 we use the
|
|
// pck_div counter to sync our other signals off it
|
|
// we read the ADC value when pck_cnt=7 and shift it out on counts 8..15
|
|
always @(posedge pck0)
|
|
begin
|
|
if((pck_cnt == 8'd7) && !pck_divclk)
|
|
to_arm_shiftreg <= adc_d;
|
|
else begin
|
|
to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
|
|
// simulation showed a glitch occuring due to the LSB of the shifter
|
|
// not being set as we shift bits out
|
|
// this ensures the ssp_din remains low after a transfer and suppresses
|
|
// the glitch that would occur when the last data shifted out ended in
|
|
// a 1 bit and the next data shifted out started with a 0 bit
|
|
to_arm_shiftreg[0] <= 1'b0;
|
|
end
|
|
end
|
|
|
|
// ADC samples on falling edge of adc_clk, data available on the rising edge
|
|
|
|
// example of ssp transfer of binary value 1100101
|
|
// start of transfer is indicated by the rise of the ssp_frame signal
|
|
// ssp_din changes on the rising edge of the ssp_clk clock and is clocked into
|
|
// the ARM by the falling edge of ssp_clk
|
|
// _______________________________
|
|
// ssp_frame__| |__
|
|
// _______ ___ ___
|
|
// ssp_din __| |_______| |___| |______
|
|
// _ _ _ _ _ _ _ _ _ _
|
|
// ssp_clk |_| |_| |_| |_| |_| |_| |_| |_| |_| |_
|
|
|
|
// serialized SSP data is gated by ant_lo to suppress unwanted signal
|
|
assign ssp_din = to_arm_shiftreg[7] && !pck_divclk;
|
|
// SSP clock always runs at 24Mhz
|
|
assign ssp_clk = pck0;
|
|
// SSP frame is gated by ant_lo and goes high when pck_divider=8..15
|
|
assign ssp_frame = (pck_cnt[7:3] == 5'd1) && !pck_divclk;
|
|
// unused signals tied low
|
|
assign pwr_hi = 1'b0;
|
|
assign pwr_oe1 = 1'b0;
|
|
assign pwr_oe2 = 1'b0;
|
|
assign pwr_oe3 = 1'b0;
|
|
assign pwr_oe4 = 1'b0;
|
|
// this is the antenna driver signal
|
|
assign pwr_lo = lf_field & pck_divclk;
|
|
// ADC clock out of phase with antenna driver
|
|
assign adc_clk = ~pck_divclk;
|
|
// ADC clock also routed to debug pin
|
|
assign dbg = adc_clk;
|
|
endmodule
|