proxmark3/armsrc/fpgaloader.c

//-----------------------------------------------------------------------------
// Copyright (C) Jonathan Westhues, April 2006
// Copyright (C) Proxmark3 contributors. See AUTHORS.md for details.
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
// GNU General Public License for more details.
//
// See LICENSE.txt for the text of the license.
//-----------------------------------------------------------------------------
// Routines to load the FPGA image, and then to configure the FPGA's major
// mode once it is configured.
//-----------------------------------------------------------------------------
#include "fpgaloader.h"

#include "proxmark3_arm.h"
#include "appmain.h"
#include "BigBuf.h"
#include "ticks.h"
#include "dbprint.h"
#include "util.h"
#include "fpga.h"
#include "string.h"

#include "lz4.h"       // uncompress

typedef struct {
    LZ4_streamDecode_t *lz4StreamDecode;
    char *next_in;
    int avail_in;
} lz4_stream_t;

typedef lz4_stream_t *lz4_streamp_t;

// remember which version of the bitstream we have already downloaded to the FPGA
static int downloaded_bitstream = 0;

// this is where the bitstreams are located in memory:
extern uint32_t _binary_obj_fpga_all_bit_z_start[], _binary_obj_fpga_all_bit_z_end[];

static uint8_t *fpga_image_ptr = NULL;
static uint32_t uncompressed_bytes_cnt;

//-----------------------------------------------------------------------------
// Set up the Serial Peripheral Interface as master
// Used to write the FPGA config word
// May also be used to write to other SPI attached devices like an LCD
//-----------------------------------------------------------------------------
static void DisableSpi(void) {
    //* Reset all the Chip Select register
    AT91C_BASE_SPI->SPI_CSR[0] = 0;
    AT91C_BASE_SPI->SPI_CSR[1] = 0;
    AT91C_BASE_SPI->SPI_CSR[2] = 0;
    AT91C_BASE_SPI->SPI_CSR[3] = 0;

    // Reset the SPI mode
    AT91C_BASE_SPI->SPI_MR = 0;

    // Disable all interrupts
    AT91C_BASE_SPI->SPI_IDR = 0xFFFFFFFF;

    // SPI disable
    AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIDIS;
}

void SetupSpi(int mode) {
    // PA1  -> SPI_NCS3 chip select (MEM)
    // PA10 -> SPI_NCS2 chip select (LCD)
    // PA11 -> SPI_NCS0 chip select (FPGA)
    // PA12 -> SPI_MISO Master-In Slave-Out
    // PA13 -> SPI_MOSI Master-Out Slave-In
    // PA14 -> SPI_SPCK Serial Clock

    // Disable PIO control of the following pins, allows use by the SPI peripheral
    AT91C_BASE_PIOA->PIO_PDR = GPIO_NCS0 | GPIO_MISO | GPIO_MOSI | GPIO_SPCK;

    // Peripheral A
    AT91C_BASE_PIOA->PIO_ASR = GPIO_NCS0 | GPIO_MISO | GPIO_MOSI | GPIO_SPCK;

    // Peripheral B
    //AT91C_BASE_PIOA->PIO_BSR |= GPIO_NCS2;

    //enable the SPI Peripheral clock
    AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_SPI);
    // Enable SPI
    AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIEN;

    switch (mode) {
        case SPI_FPGA_MODE:
            AT91C_BASE_SPI->SPI_MR =
                (0 << 24)          |  // Delay between chip selects (take default: 6 MCK periods)
                (0xE << 16)         | // Peripheral Chip Select (selects FPGA SPI_NCS0 or PA11)
                (0 << 7)           |  // Local Loopback Disabled
                AT91C_SPI_MODFDIS   | // Mode Fault Detection disabled
                (0 << 2)           |  // Chip selects connected directly to peripheral
                AT91C_SPI_PS_FIXED  | // Fixed Peripheral Select
                AT91C_SPI_MSTR;       // Master Mode

            AT91C_BASE_SPI->SPI_CSR[0] =
                (1 << 24)          |  // Delay between Consecutive Transfers (32 MCK periods)
                (1 << 16)          |  // Delay Before SPCK (1 MCK period)
                (6 << 8)           |  // Serial Clock Baud Rate (baudrate = MCK/6 = 24MHz/6 = 4M baud
                AT91C_SPI_BITS_16   | // Bits per Transfer (16 bits)
                (0 << 3)           |  // Chip Select inactive after transfer
                AT91C_SPI_NCPHA     | // Clock Phase data captured on leading edge, changes on following edge
                (0 << 0);             // Clock Polarity inactive state is logic 0
            break;
        /*
                    case SPI_LCD_MODE:
                    AT91C_BASE_SPI->SPI_MR =
                        ( 0 << 24)          | // Delay between chip selects (take default: 6 MCK periods)
                        (0xB << 16)         | // Peripheral Chip Select (selects LCD SPI_NCS2 or PA10)
                        ( 0 << 7)           | // Local Loopback Disabled
                        ( 1 << 4)           | // Mode Fault Detection disabled
                        ( 0 << 2)           | // Chip selects connected directly to peripheral
                        ( 0 << 1)           | // Fixed Peripheral Select
                        ( 1 << 0);            // Master Mode

                    AT91C_BASE_SPI->SPI_CSR[2] =
                        ( 1 << 24)          | // Delay between Consecutive Transfers (32 MCK periods)
                        ( 1 << 16)          | // Delay Before SPCK (1 MCK period)
                        ( 6 << 8)           | // Serial Clock Baud Rate (baudrate = MCK/6 = 24MHz/6 = 4M baud
                        AT91C_SPI_BITS_9    | // Bits per Transfer (9 bits)
                        ( 0 << 3)           | // Chip Select inactive after transfer
                        ( 1 << 1)           | // Clock Phase data captured on leading edge, changes on following edge
                        ( 0 << 0);            // Clock Polarity inactive state is logic 0
                    break;
        */
        default:
            DisableSpi();
            break;
    }
}

//-----------------------------------------------------------------------------
// Set up the synchronous serial port with the set of options that fits
// the FPGA mode. Both RX and TX are always enabled.
//-----------------------------------------------------------------------------
void FpgaSetupSsc(uint16_t fpga_mode) {
    // First configure the GPIOs, and get ourselves a clock.
    AT91C_BASE_PIOA->PIO_ASR =
        GPIO_SSC_FRAME  |
        GPIO_SSC_DIN    |
        GPIO_SSC_DOUT   |
        GPIO_SSC_CLK;
    AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT;

    AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_SSC);

    // Now set up the SSC proper, starting from a known state.
    AT91C_BASE_SSC->SSC_CR = AT91C_SSC_SWRST;

    // RX clock comes from TX clock, RX starts on Transmit Start,
    // data and frame signal is sampled on falling edge of RK
    AT91C_BASE_SSC->SSC_RCMR = SSC_CLOCK_MODE_SELECT(1) | SSC_CLOCK_MODE_START(1);

    // 8, 16 or 32 bits per transfer, no loopback, MSB first, 1 transfer per sync
    // pulse, no output sync
    if (((fpga_mode & FPGA_MAJOR_MODE_MASK) == FPGA_MAJOR_MODE_HF_READER ||
            (fpga_mode & FPGA_MAJOR_MODE_MASK) == FPGA_MAJOR_MODE_HF_FSK_READER) &&
            (FpgaGetCurrent() == FPGA_BITSTREAM_HF || FpgaGetCurrent() == FPGA_BITSTREAM_HF_15)) {
        AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(16) | AT91C_SSC_MSBF | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0);
    } else {
        AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(8) | AT91C_SSC_MSBF | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0);
    }

    // TX clock comes from TK pin, no clock output, outputs change on rising edge of TK,
    // TF (frame sync) is sampled on falling edge of TK, start TX on rising edge of TF
    AT91C_BASE_SSC->SSC_TCMR = SSC_CLOCK_MODE_SELECT(2) | SSC_CLOCK_MODE_START(5);

    // tx framing is the same as the rx framing
    AT91C_BASE_SSC->SSC_TFMR = AT91C_BASE_SSC->SSC_RFMR;

    AT91C_BASE_SSC->SSC_CR = AT91C_SSC_RXEN | AT91C_SSC_TXEN;
}

//-----------------------------------------------------------------------------
// Set up DMA to receive samples from the FPGA. We will use the PDC, with
// a single buffer as a circular buffer (so that we just chain back to
// ourselves, not to another buffer).
//-----------------------------------------------------------------------------
bool FpgaSetupSscDma(uint8_t *buf, uint16_t len) {
    if (buf == NULL) return false;

    FpgaDisableSscDma();
    AT91C_BASE_PDC_SSC->PDC_RPR = (uint32_t) buf;  // transfer to this memory address
    AT91C_BASE_PDC_SSC->PDC_RCR = len;             // transfer this many bytes
    AT91C_BASE_PDC_SSC->PDC_RNPR = (uint32_t) buf; // next transfer to same memory address
    AT91C_BASE_PDC_SSC->PDC_RNCR = len;            // ... with same number of bytes
    FpgaEnableSscDma();
    return true;
}

//----------------------------------------------------------------------------
// Uncompress (inflate) the FPGA data. Returns one decompressed byte with each call.
//----------------------------------------------------------------------------
static int get_from_fpga_combined_stream(lz4_streamp_t compressed_fpga_stream, uint8_t *output_buffer) {
    if (fpga_image_ptr == output_buffer + FPGA_RING_BUFFER_BYTES) { // need more data
        fpga_image_ptr = output_buffer;
        int cmp_bytes;
        memcpy(&cmp_bytes, compressed_fpga_stream->next_in, sizeof(int));
        compressed_fpga_stream->next_in += 4;
        compressed_fpga_stream->avail_in -= cmp_bytes + 4;
        int res = LZ4_decompress_safe_continue(compressed_fpga_stream->lz4StreamDecode,
                                               compressed_fpga_stream->next_in,
                                               (char *)output_buffer,
                                               cmp_bytes,
                                               FPGA_RING_BUFFER_BYTES);
        if (res <= 0) {
            Dbprintf("inflate returned: %d", res);
            return res;
        }
        compressed_fpga_stream->next_in += cmp_bytes;
    }
    uncompressed_bytes_cnt++;
    return *fpga_image_ptr++;
}

//----------------------------------------------------------------------------
// Undo the interleaving of several FPGA config files. FPGA config files
// are combined into one big file:
// 288 bytes from FPGA file 1, followed by 288 bytes from FGPA file 2, etc.
//----------------------------------------------------------------------------
static int get_from_fpga_stream(int bitstream_version, lz4_streamp_t compressed_fpga_stream, uint8_t *output_buffer) {
    while ((uncompressed_bytes_cnt / FPGA_INTERLEAVE_SIZE) % g_fpga_bitstream_num != (bitstream_version - 1)) {
        // skip undesired data belonging to other bitstream_versions
        get_from_fpga_combined_stream(compressed_fpga_stream, output_buffer);
    }

    return get_from_fpga_combined_stream(compressed_fpga_stream, output_buffer);
}

//----------------------------------------------------------------------------
// Initialize decompression of the respective (HF or LF) FPGA stream
//----------------------------------------------------------------------------
static bool reset_fpga_stream(int bitstream_version, lz4_streamp_t compressed_fpga_stream, uint8_t *output_buffer) {
    uint8_t header[FPGA_BITSTREAM_FIXED_HEADER_SIZE];

    uncompressed_bytes_cnt = 0;

    // initialize z_stream structure for inflate:
    compressed_fpga_stream->next_in = (char *)_binary_obj_fpga_all_bit_z_start;
    compressed_fpga_stream->avail_in = (uint32_t)_binary_obj_fpga_all_bit_z_end - (uint32_t)_binary_obj_fpga_all_bit_z_start;

    int res = LZ4_setStreamDecode(compressed_fpga_stream->lz4StreamDecode, NULL, 0);
    if (res == 0)
        return false;

    fpga_image_ptr = output_buffer + FPGA_RING_BUFFER_BYTES;

    for (uint16_t i = 0; i < FPGA_BITSTREAM_FIXED_HEADER_SIZE; i++)
        header[i] = get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer);

    // Check for a valid .bit file (starts with bitparse_fixed_header)
    if (memcmp(bitparse_fixed_header, header, FPGA_BITSTREAM_FIXED_HEADER_SIZE) == 0)
        return true;

    return false;
}

static void DownloadFPGA_byte(uint8_t w) {
#define SEND_BIT(x) { if(w & (1<<x) ) HIGH(GPIO_FPGA_DIN); else LOW(GPIO_FPGA_DIN); HIGH(GPIO_FPGA_CCLK); LOW(GPIO_FPGA_CCLK); }
    SEND_BIT(7);
    SEND_BIT(6);
    SEND_BIT(5);
    SEND_BIT(4);
    SEND_BIT(3);
    SEND_BIT(2);
    SEND_BIT(1);
    SEND_BIT(0);
}

// Download the fpga image starting at current stream position with length FpgaImageLen bytes
static void DownloadFPGA(int bitstream_version, int FpgaImageLen, lz4_streamp_t compressed_fpga_stream, uint8_t *output_buffer) {
    int i = 0;
#if !defined XC3
    AT91C_BASE_PIOA->PIO_OER = GPIO_FPGA_ON;
    AT91C_BASE_PIOA->PIO_PER = GPIO_FPGA_ON;
    HIGH(GPIO_FPGA_ON);  // ensure everything is powered on
#endif

    SpinDelay(50);

    LED_D_ON();

    // These pins are inputs
    AT91C_BASE_PIOA->PIO_ODR =
        GPIO_FPGA_NINIT |
        GPIO_FPGA_DONE;
    // PIO controls the following pins
    AT91C_BASE_PIOA->PIO_PER =
        GPIO_FPGA_NINIT |
#if defined XC3
        //3S100E M2 & M3 PIO ENA
        GPIO_SPCK |
        GPIO_MOSI |
#endif
        GPIO_FPGA_DONE;

    // Enable pull-ups
    AT91C_BASE_PIOA->PIO_PPUER =
        GPIO_FPGA_NINIT |
        GPIO_FPGA_DONE;

    // setup initial logic state
    HIGH(GPIO_FPGA_NPROGRAM);
    LOW(GPIO_FPGA_CCLK);
    LOW(GPIO_FPGA_DIN);
    // These pins are outputs
    AT91C_BASE_PIOA->PIO_OER =
        GPIO_FPGA_NPROGRAM |
        GPIO_FPGA_CCLK     |
#if defined XC3
        //3S100E M2 & M3 OUTPUT ENA
        GPIO_SPCK |
        GPIO_MOSI |
#endif
        GPIO_FPGA_DIN;

#if defined XC3
    //3S100E M2 & M3 OUTPUT HIGH
    HIGH(GPIO_SPCK);
    HIGH(GPIO_MOSI);
#endif

    // enter FPGA configuration mode
    LOW(GPIO_FPGA_NPROGRAM);
    SpinDelay(50);
    HIGH(GPIO_FPGA_NPROGRAM);

    i = 100000;
    // wait for FPGA ready to accept data signal
    while ((i) && (!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_NINIT))) {
        i--;
    }

    // crude error indicator, leave both red LEDs on and return
    if (i == 0) {
        LED_C_ON();
        LED_D_ON();
        return;
    }

#if defined XC3
    //3S100E M2 & M3 RETURN TO NORMAL
    LOW(GPIO_SPCK);
    LOW(GPIO_MOSI);
    AT91C_BASE_PIOA->PIO_PDR = GPIO_SPCK | GPIO_MOSI;
#endif

    for (i = 0; i < FpgaImageLen; i++) {
        int b = get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer);
        if (b < 0) {
            Dbprintf("Error %d during FpgaDownload", b);
            break;
        }
        DownloadFPGA_byte(b);
    }

    // continue to clock FPGA until ready signal goes high
    i = 100000;
    while ((i--) && (!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_DONE))) {
        HIGH(GPIO_FPGA_CCLK);
        LOW(GPIO_FPGA_CCLK);
    }
    // crude error indicator, leave both red LEDs on and return
    if (i == 0) {
        LED_C_ON();
        LED_D_ON();
        return;
    }
    LED_D_OFF();
}

/* Simple Xilinx .bit parser. The file starts with the fixed opaque byte sequence
 * 00 09 0f f0 0f f0 0f f0 0f f0 00 00 01
 * After that the format is 1 byte section type (ASCII character), 2 byte length
 * (big endian), <length> bytes content. Except for section 'e' which has 4 bytes
 * length.
 */
static int bitparse_find_section(int bitstream_version, char section_name, uint32_t *section_length, lz4_streamp_t compressed_fpga_stream, uint8_t *output_buffer) {

#define MAX_FPGA_BIT_STREAM_HEADER_SEARCH 100  // maximum number of bytes to search for the requested section

    int result = 0;
    uint16_t numbytes = 0;
    while (numbytes < MAX_FPGA_BIT_STREAM_HEADER_SEARCH) {
        char current_name = get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer);
        numbytes++;
        uint16_t current_length = 0;
        if (current_name < 'a' || current_name > 'e') {
            /* Strange section name, abort */
            break;
        }
        current_length = 0;
        switch (current_name) {
            case 'e':
                /* Four byte length field */
                current_length += get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer) << 24;
                current_length += get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer) << 16;
                numbytes += 2;
            default: /* Fall through, two byte length field */
                current_length += get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer) << 8;
                current_length += get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer) << 0;
                numbytes += 2;
        }

        if (current_name != 'e' && current_length > 255) {
            /* Maybe a parse error */
            break;
        }

        if (current_name == section_name) {
            /* Found it */
            *section_length = current_length;
            result = 1;
            break;
        }

        for (uint16_t i = 0; i < current_length && numbytes < MAX_FPGA_BIT_STREAM_HEADER_SEARCH; i++) {
            get_from_fpga_stream(bitstream_version, compressed_fpga_stream, output_buffer);
            numbytes++;
        }
    }
    return result;
}

//----------------------------------------------------------------------------
// Change FPGA image status, if image loaded.
// bitstream_version is your new fpga image version
// return true if can change.
// return false if image is unloaded.
//----------------------------------------------------------------------------
#if defined XC3
static bool FpgaConfCurrentMode(int bitstream_version) {
    // fpga "XC3S100E" image merge
    // If fpga image is no init
    // We need load hf_lf_allinone.bit
    if (downloaded_bitstream != 0) {
        // test start
        // PIO controls the following pins
        AT91C_BASE_PIOA->PIO_PER = GPIO_FPGA_SWITCH;
        // These pins are outputs
        AT91C_BASE_PIOA->PIO_OER = GPIO_FPGA_SWITCH;

        // try to turn off antenna
        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);

        if (bitstream_version == FPGA_BITSTREAM_LF) {
            LOW(GPIO_FPGA_SWITCH);
        } else {
            HIGH(GPIO_FPGA_SWITCH);
        }
        // update downloaded_bitstream
        downloaded_bitstream = bitstream_version;
        // turn off antenna
        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        return true;
    }
    return false;
}
#endif

//----------------------------------------------------------------------------
// Check which FPGA image is currently loaded (if any). If necessary
// decompress and load the correct (HF or LF) image to the FPGA
//----------------------------------------------------------------------------
void FpgaDownloadAndGo(int bitstream_version) {

    // check whether or not the bitstream is already loaded
    if (downloaded_bitstream == bitstream_version) {
        FpgaEnableTracing();
        return;
    }

#if defined XC3
    // If we can change image version
    // direct return.
    if (FpgaConfCurrentMode(bitstream_version)) {
        return;
    }
#endif

    // Send waiting time extension request as this will take a while
    send_wtx(1500);

    bool verbose = (g_dbglevel > 3);

    // make sure that we have enough memory to decompress
    BigBuf_free();
    BigBuf_Clear_ext(verbose);

    lz4_stream_t compressed_fpga_stream;
    LZ4_streamDecode_t lz4StreamDecode_body = {{ 0 }};
    compressed_fpga_stream.lz4StreamDecode = &lz4StreamDecode_body;
    uint8_t *output_buffer = BigBuf_malloc(FPGA_RING_BUFFER_BYTES);

    if (!reset_fpga_stream(bitstream_version, &compressed_fpga_stream, output_buffer))
        return;

    uint32_t bitstream_length;
    if (bitparse_find_section(bitstream_version, 'e', &bitstream_length, &compressed_fpga_stream, output_buffer)) {
        DownloadFPGA(bitstream_version, bitstream_length, &compressed_fpga_stream, output_buffer);
        downloaded_bitstream = bitstream_version;
    }

#if defined XC3
    // first download fpga image to hf
    // we need to change fpga status to hf
    FpgaConfCurrentMode(bitstream_version);
#endif

    // turn off antenna
    FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);

    // free eventually allocated BigBuf memory
    BigBuf_free();
    BigBuf_Clear_ext(false);
}

//-----------------------------------------------------------------------------
// Send a 16 bit command/data pair to the FPGA.
// The bit format is:  C3 C2 C1 C0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
// where C is the 4 bit command and D is the 12 bit data
//
// @params cmd and v  gets OR:ED over each other.  Take careful note of overlapping bits.
//-----------------------------------------------------------------------------
void FpgaSendCommand(uint16_t cmd, uint16_t v) {
    SetupSpi(SPI_FPGA_MODE);
    while ((AT91C_BASE_SPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0); // wait for the transfer to complete
    AT91C_BASE_SPI->SPI_TDR = AT91C_SPI_LASTXFER | cmd | v;    // send the data
    while (!(AT91C_BASE_SPI->SPI_SR & AT91C_SPI_RDRF)) {};     // wait till transfer is complete
}
//-----------------------------------------------------------------------------
// Write the FPGA setup word (that determines what mode the logic is in, read
// vs. clone vs. etc.). This is now a special case of FpgaSendCommand() to
// avoid changing this function's occurrence everywhere in the source code.
//-----------------------------------------------------------------------------
void FpgaWriteConfWord(uint16_t v) {
    FpgaSendCommand(FPGA_CMD_SET_CONFREG, v);
}

//-----------------------------------------------------------------------------
// enable/disable FPGA internal tracing
//-----------------------------------------------------------------------------
void FpgaEnableTracing(void) {
    FpgaSendCommand(FPGA_CMD_TRACE_ENABLE, 1);
}

void FpgaDisableTracing(void) {
    FpgaSendCommand(FPGA_CMD_TRACE_ENABLE, 0);
}

//-----------------------------------------------------------------------------
// Set up the CMOS switches that mux the ADC: four switches, independently
// closable, but should only close one at a time. Not an FPGA thing, but
// the samples from the ADC always flow through the FPGA.
//-----------------------------------------------------------------------------
void SetAdcMuxFor(uint32_t whichGpio) {

#ifndef WITH_FPC_USART
    // When compiled without FPC USART support
    AT91C_BASE_PIOA->PIO_OER =
        GPIO_MUXSEL_HIPKD |
        GPIO_MUXSEL_LOPKD |
        GPIO_MUXSEL_LORAW |
        GPIO_MUXSEL_HIRAW;

    AT91C_BASE_PIOA->PIO_PER =
        GPIO_MUXSEL_HIPKD |
        GPIO_MUXSEL_LOPKD |
        GPIO_MUXSEL_LORAW |
        GPIO_MUXSEL_HIRAW;

    LOW(GPIO_MUXSEL_HIPKD);
    LOW(GPIO_MUXSEL_LOPKD);
    LOW(GPIO_MUXSEL_HIRAW);
    LOW(GPIO_MUXSEL_LORAW);
    HIGH(whichGpio);
#else
    if ((whichGpio == GPIO_MUXSEL_LORAW) || (whichGpio == GPIO_MUXSEL_HIRAW))
        return;
    // FPC USART uses HIRAW/LOWRAW pins, so they are excluded here.
    AT91C_BASE_PIOA->PIO_OER = GPIO_MUXSEL_HIPKD | GPIO_MUXSEL_LOPKD;
    AT91C_BASE_PIOA->PIO_PER = GPIO_MUXSEL_HIPKD | GPIO_MUXSEL_LOPKD;
    LOW(GPIO_MUXSEL_HIPKD);
    LOW(GPIO_MUXSEL_LOPKD);
    HIGH(whichGpio);
#endif

}

void Fpga_print_status(void) {
    DbpString(_CYAN_("Current FPGA image"));
    Dbprintf("  mode....................%s", g_fpga_version_information[downloaded_bitstream - 1]);
}

int FpgaGetCurrent(void) {
    return downloaded_bitstream;
}

// Turns off the antenna,
// log message
// if HF,  Disable SSC DMA
// turn off trace and leds off.
void switch_off(void) {
    if (g_dbglevel > 3) {
        Dbprintf("switch_off");
    }

    FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
    if (downloaded_bitstream == FPGA_BITSTREAM_HF || downloaded_bitstream == FPGA_BITSTREAM_HF_15) {
        FpgaDisableSscDma();
    }

    set_tracing(false);
    LEDsoff();
}