28 KiB
T5577 Introduction Guide
Based on RRG/Iceman Proxmark3 repo
Ver.1 8 Sep 2019
Ver.2 7 March 2021
Table of Contents
Part 1
^Top
Introduction
^Top
The T5577 is a generic LF (Low Frequency) RFID card that is used in the 125 Khz frequency space. It is a good card to use to learn about RFID and learn how to use the proxmark3.
It is highly recommended that when learning about RFID that learning how to read the data sheets be near the top of the list. It can be very hard as the data sheet will hold the information you need, but you don’t yet know what it means. As such, I will attempt to point to sections of the data sheet and would highly advise that you look at the data sheet as you go. Overtime the data sheet may change, as a result things may not always be referenced correctly.
As at writing this guide, the data sheet can be found at :
http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-9187-RFID-ATA5577C_Datasheet.pdf
This guide is not a how do I clone document. It is meant to help people learn how to use the T5577 and in the process learn about rfid and the proxmark3.
Throughout this guide I will give examples. It is recommended that you try these as we go. To do so, have a blank T5577 card that you can use for this purpose.
T5577 Overview
^Top
The T5577 is a chip that can hold data and a configuration (Section 4.12).
In the diagram below, all white blocks can hold data. Some can be used for a second purpose, such as the ‘password’ and ‘traceability data’. The ‘Configuration Data’ and ‘Analog front end option setup’ will tell the chip how to behave.
What data is on my T5577
^Top
Let’s have a look and see what a card might look like in the proxmark3 software. Since we can change the configuration of how the T5577 will output data, the proxmark3 software needs to work out how to interpret the data it receives, we do this with the following command.
It should be noted that the T5577 has many clones. As such the default setup of each card may be different. If the tractability data is present, then this will vary based on the batch of cards.
Always run this command when you place a t5577 on the proxmark3. In all examples shown, it will be assumed you have run the detect command.
[usb] pm3 --> lf t55xx detect
You should see a results similar to the following:
[=] Chip type......... T55x7
[=] Modulation........ ASK
[=] Bit rate.......... 2 - RF/32
[=] Inverted.......... No
[=] Offset............ 33
[=] Seq. terminator... Yes
[=] Block0............ 000880E0 (auto detect)
[=] Downlink mode..... default/fixed bit length
[=] Password set...... No
Now that the proxmark3 has detected a T55x7 chip, and found some information about it, we should be able to see all the data on the chip.
[usb] pm3 --> lf t55xx dump
Your results should look similar to the following:
[+] Reading Page 0:
[+] blk | hex data | binary | ascii
[+] ----+----------+----------------------------------+-------
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
[+] 04 | 00000000 | 00000000000000000000000000000000 | ....
[+] 05 | 00000000 | 00000000000000000000000000000000 | ....
[+] 06 | 00000000 | 00000000000000000000000000000000 | ....
[+] 07 | 00000000 | 00000000000000000000000000000000 | ....
[+] Reading Page 1:
[+] blk | hex data | binary | ascii
[+] ----+----------+----------------------------------+-------
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
I will cover the meaning of this data as we go, but for now, lets keep it simple.
Read and Write Blocks of Data
^Top
The basic function of using the proxmark3 with rfid cards is to read and write data. This reading and writing must be done in the correct way needed for the chip (and its configuration). Lucky for us, the developers have done a great job and gave us commands. What we need to know is that with the T5577, data is read/written one complete block at a time. Each block holds 32 bits of data (hence the binary output shown)
Since we know that the card has data and configuration blocks, lets say away from those while we learn how to read and write. I suggest you follow along and perform each command and check the results as we go.
We can store our own data in blocks 1-7 (remember that block 7 will be needed if we want to set a password).
(Don’t forget to run the detect command: lf t55xx detect, and ensure you can see the card)
-
Check what is stored in block 1. The following command can be read as, run a low frequency (lf) command for the T55xx chip (t55xx) and read block (b) number 1.
[usb] pm3 --> lf t55xx read -b 1result:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [+] 01 | 00000000 | 00000000000000000000000000000000 | ....Note: Depending on the history of your card, your data may vary, but should match the dump data.
-
Write some new data into block 1 on the card.
We use the -d option to supply the data ‘12345678’
[usb] pm3 --> lf t55xx write -b 1 -d 12345678result:
[=] Writing page 0 block: 01 data: 0x12345678 -
Now, lets check if the data was written.
[usb] pm3 --> lf t55xx read -b 1result:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [+] 01 | 12345678 | 00010010001101000101011001111000 | .4Vx -
The data is written in Hexadecimal. A single hex digit holds 4 bits of data. So to store 32 bits in a block, we need to supply 8 hex digits (8 * 4 = 32). If you are not familiar with hex and binary do a little bit of home work to learn. The following is a quick start.
Hex Binary Decimal 0 0000 0 1 0001 1 2 0010 2 3 0011 3 4 0100 4 5 0101 5 6 0110 6 7 0111 7 8 1000 8 9 1001 9 A 1010 10 B 1011 11 C 1100 12 D 1101 13 E 1110 14 F 1111 15 To use all the bits we supply the data in Hex format and it will always be 8 hex digits.
Lets try and write 89ABCDEF
[usb] pm3 --> lf t55xx write -b 1 -d 89abcdefresult:
[=] Writing page 0 block: 01 data: 0x89ABCDEFand check
[usb] pm3 --> lf t55xx read -b 1result:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [+] 01 | 89ABCDEF | 10001001101010111100110111101111 | ....
Exercise 1
^Top
Using the read and write commands you have learnt see if you can make the lf t55 dump command show the following data for blocks 1-7 (Page 0). Do not write to block 0 or try and change the data on page 1.
[usb] pm3 --> lf t55 dump
result:
[+] Reading Page 0:
[+] blk | hex data | binary | ascii
[+] ----+----------+----------------------------------+-------
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
[+] 01 | 89ABCDEF | 10001001101010111100110111101111 | ....
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
[+] 04 | 00000000 | 00000000000000000000000000000000 | ....
[+] 05 | 00000000 | 00000000000000000000000000000000 | ....
[+] 06 | 00000000 | 00000000000000000000000000000000 | ....
[+] 07 | 00000000 | 00000000000000000000000000000000 | ....
[+] Reading Page 1:
[+] blk | hex data | binary | ascii
[+] ----+----------+----------------------------------+-------
[+] 00 | 000880E0 | 00000000000010001000000011100000 | ....
[+] 01 | 00000000 | 00000000000000000000000000000000 | ....
[+] 02 | 00000000 | 00000000000000000000000000000000 | ....
[+] 03 | 00000000 | 00000000000000000000000000000000 | ....
Practice reading and writing to blocks 1 to 6 until you are happy you can do it and get the results you wanted (i.e. the data you want stored is written to the block you want it stored in). I recommend staying away from block 7 as this is where the password is stored, if used. If you forget this data/password, you won't be able to read or write to the card.
How do I use a password
^Top
This can be a little tricky for beginners. If you forget your password you will lose access to your card.
To tell the T5577 to use a password, we have to change the data in the configuration block (0). To help learn this and make it as simple as I can, please read and follow exactly. If your results DON’T match 100% as required, please do not proceed.
-
Lets start with a known card state and wipe the card. This will set a default configuration to block 0 and set all the data in blocks 1-7 to a default.
[usb] pm3 --> lf t55xx wipeResult:
[=] Target T55x7 tag [=] Default configuration block 000880E0 [=] Begin wiping... [=] Writing page 0 block: 00 data: 0x000880E0 [=] Writing page 0 block: 01 data: 0x00000000 [=] Writing page 0 block: 02 data: 0x00000000 [=] Writing page 0 block: 03 data: 0x00000000 [=] Writing page 0 block: 04 data: 0x00000000 [=] Writing page 0 block: 05 data: 0x00000000 [=] Writing page 0 block: 06 data: 0x00000000 [=] Writing page 0 block: 07 data: 0x00000000 -
Check that the card is in the desired state.
[usb] pm3 --> lf t55xx detectresult:
[=] Chip type......... T55x7 [=] Modulation........ ASK [=] Bit rate.......... 2 - RF/32 [=] Inverted.......... No [=] Offset............ 33 [=] Seq. terminator... Yes [=] Block0............ 000880E0 (auto detect) [=] Downlink mode..... default/fixed bit length [=] Password set...... NoIf block 0 does not hold the hex data 0x00088040 resolve this first before proceeding.
-
Set the password we want to use. For this example lets use the password : 12345678
The password is saved in block 7 of page 0.
[usb] pm3 --> lf t55xx write -b 7 -d 12345678result:
[=] Writing page 0 block: 07 data: 0x12345678 -
Lets verify both block 0 and block 7
[usb] pm3 --> lf t55xx dumpresult:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [+] 00 | 000880E0 | 00000000000010001000000011100000 | .... [+] 01 | 00000000 | 00000000000000000000000000000000 | .... [+] 02 | 00000000 | 00000000000000000000000000000000 | .... [+] 03 | 00000000 | 00000000000000000000000000000000 | .... [+] 04 | 00000000 | 00000000000000000000000000000000 | .... [+] 05 | 00000000 | 00000000000000000000000000000000 | .... [+] 06 | 00000000 | 00000000000000000000000000000000 | .... [+] 07 | 12345678 | 00010010001101000101011001111000 | .4Vx [+] Reading Page 1: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [+] 00 | 000880E0 | 00000000000010001000000011100000 | .... [+] 01 | 00000000 | 00000000000000000000000000000000 | .... [+] 02 | 00000000 | 00000000000000000000000000000000 | .... [+] 03 | 00000000 | 00000000000000000000000000000000 | ....Important : If block 0 and block 7 don’t match exactly, do not continue.
-
Now we have a known configuration block and a known password of 12345678, we are ready to tell the card to use the password.
To do this the datasheet tells us we need to set the 28th bit “PWD”. Check your datasheet and see the entire table (remember the data sheet is your friend).
We will cover other things in the configuration later. But the key note here, is we ONLY want to change bit 28 and nothing else.
Current Block 0 : 00088040
New Block 0 : 00088050To understand what happened to get from 00088040 to 00088050 we need to look at the binary data.
While this can be confusing, it is important to understand this as we do more advanced things.
Bit Location (28)
000000000011111111112222222 2 2233
123456789012345678901234567 8 9012Hex Data Binary Data 00088040 00000000000010001000000001000000 00088050 00000000000010001000000001010000 See how in the above we changed the bit in location 28 from a 0 to 1
0 = No Password, 1 = Use PasswordNote how we did NOT change any other part of the configuration, only bit 28.
To re-cap.
We put the card into a known configuration Block 0 : 00088040
We set the a known password Block 7 : 12345678
We altered the config data to tell the T5577 to use the password.
New Block 0 : 00088050If you have completed all steps and have the exact same results, we are ready to apply the new configuration.
[usb] pm3 --> lf t55xx write -b 0 -d 00088050result:
[=] Writing page 0 block: 00 data: 0x00088050 -
Lets check what happens when the password is set.
[usb] pm3 --> lf t55 detectresult:
[!] Could not detect modulation automatically. Try setting it manually with 'lf t55xx config'Note how the lf t55 detect no longer seems to work!
In this case, this is due to needing a password to read/write to the card.
Lets try again, but this time supply the password. We use the option -p followed by the password.
[usb] pm3 --> lf t55 detect -p 12345678result:
[=] Chip type......... T55x7 [=] Modulation........ ASK [=] Bit rate.......... 2 - RF/32 [=] Inverted.......... No [=] Offset............ 33 [=] Seq. terminator... Yes [=] Block0............ 00088050 (auto detect) [=] Downlink mode..... default/fixed bit length [=] Password set...... Yes [=] Password.......... 12345678 -
Write a block of data with a password
[usb] pm3 --> lf t55xx write -b 1 -d 1234abcd -p 12345678result:
[=] Writing page 0 block: 01 data: 0x1234ABCD pwd: 0x12345678 -
Read a block of data with a password
**** Important ****
Reading a T5577 block with a password when a password is not enabled can result in locking the card. Please only use read with a password when it is known that a password is in use.
The proxmark3 has a safety check!
[usb] pm3 --> lf t55xx read -b 1 -p 12345678result:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [!] Safety check: Could not detect if PWD bit is set in config block. Exits.Note that the proxmark3 did not read the block, the safety kicked in and wants us to confirm by supply the override option ‘-o’.
Lets try again with the ‘-o’ option as we know the password is set.
[usb] pm3 --> lf t55xx read -b 1 -p 12345678 -oresult:
[+] Reading Page 0: [+] blk | hex data | binary | ascii [+] ----+----------+----------------------------------+------- [=] Safety check overridden - proceeding despite risk [+] 01 | 1234ABCD | 00010010001101001010101111001101 | .4..This time, we can see the data we wrote to block 1 is found with the read command.
-
Remove the need to supply the password.
To do this we need to clear Bit 28 (set to 0) in the config. We have this from above.
Remember if we don’t know the config and write this config to the card, it will overwrite all other settings. This can recover the card, but will lose any settings you may want. So it’s a good idea to read the config, and set bit 28 to 0, rather than just overwrite the config and change the way the card works.
In our examples we know what it should be : 00088040
[usb] pm3 --> lf t55xx write -b 0 -d 00088040 -p 12345678result:
[=] Writing page 0 block: 00 data: 0x00088040 pwd: 0x12345678Now check if we can detect without a password
[usb] pm3 --> lf t55 detectresult:
[=] Chip type......... T55x7 [=] Modulation........ ASK [=] Bit rate.......... 2 - RF/32 [=] Inverted.......... No [=] Offset............ 33 [=] Seq. terminator... Yes [=] Block0............ 00088040 (auto detect) [=] Downlink mode..... default/fixed bit length [=] Password set...... NoYes we can! We can see Block 0 is the correct config 00088040
Part 2 – Configuration Blocks
^Top
One of the things a lot of people have trouble with or miss, is that the T5577 has two different and separate communications protocols, each with their own sub-protocols.
- Card to Reader
- Reader to Card
In Card to Reader, the T5577 will encode its data using the settings from Block 0 in Page 0. It will use this in both default read mode (where is sends out the blocks from 1 to x on power up), as well as when it responds to commands.
In the Reader To Card, the T5577 will encode the data using the settings from Block 3 Page 1. If the command is not encoded correctly it will ignore the command and revert back to default read mode.
The configuration Block – Block 0 Page 0
^Top
For this configuration the settings chosen will be for the purpose of the card when used in production. E.G. If you want the card to act like an EM4100, then we need to choose the settings that work like the EM4100; same goes for others like HID. I am not going to cover these here, rather use an example. Others have collected these and posted on the forum or can be found by searching the web.
To get started lets look back at the data sheet.
The non-password protect EM4100 could have a block 0 config of 00148040, so what does it mean.
To decode this config, we need to look at it in binary 00000000000101001000000001000000. Note that it had 32 bits and the config block 0 is 32 bits. Now we can break it down.
| Bits | Purpose | Value |
|---|---|---|
| 0000 | Master Key | Nothing Set |
| 0000000 | Not used in Basic Mode | |
| 101 | Data Bit Rate | RF/64 |
| 0 | Not used in Basic Mode | |
| 01000 | Modulation | Manchester |
| 00 | PSKCF | RF/2 |
| 0 | AOR | Not Set |
| 0 | Not used in Basic Mode | |
| 010 | Max Block | 2 |
| 0 | Password | Not Set |
| 0 | ST Sequence Terminator | Not Set |
| 00 | Not used in Basic Mode | |
| 0 | Init Delay | Not Set |
To get more detail on each item, read through the data sheet.
Lets see how the proxmark3 can help us learn. We will assume the T5577 is in the same state from Part 1, where we can write to the card with no password set (if not, review and get you card back to this state).
-
Lets turn you T5577 into an EM4100 with ID 1122334455
[usb] pm3 --> lf em 410x clone --id 1122334455result:
[+] Preparing to clone EM4102 to T55x7 tag with ID 1122334455 (RF/64) [#] Clock rate: 64 [#] Tag T55x7 written with 0xff8c65298c94a940 [+] Done -
Check this has work.
[usb] pm3 --> lf searchresult:
[=] NOTE: some demods output possible binary [=] if it finds something that looks like a tag [=] False Positives ARE possible [=] [=] Checking for known tags... [=] [+] EM 410x ID 0F0368568B [+] EM410x ( RF/64 ) [=] -------- Possible de-scramble patterns --------- [+] Unique TAG ID : F0C0166AD1 [=] HoneyWell IdentKey [+] DEZ 8 : 06837899 [+] DEZ 10 : 0057169547 [+] DEZ 5.5 : 00872.22155 [+] DEZ 3.5A : 015.22155 [+] DEZ 3.5B : 003.22155 [+] DEZ 3.5C : 104.22155 [+] DEZ 14/IK2 : 00064481678987 [+] DEZ 15/IK3 : 001034014845649 [+] DEZ 20/ZK : 15001200010606101301 [=] [+] Other : 22155_104_06837899 [+] Pattern Paxton : 259822731 [0xF7C948B] [+] Pattern 1 : 9750181 [0x94C6A5] [+] Pattern Sebury : 22155 104 6837899 [0x568B 0x68 0x68568B] [=] ------------------------------------------------ [+] Valid EM410x ID found! [+] Chipset detection: T55xx [?] Hint: try `lf t55xx` commandsLooks good.
-
Now lets see what the T5577 detect and info shows
[usb] pm3 --> lf t55 detectresult:
[=] Chip type......... T55x7 [=] Modulation........ ASK [=] Bit rate.......... 5 - RF/64 [=] Inverted.......... No [=] Offset............ 33 [=] Seq. terminator... Yes [=] Block0............ 00148040 (auto detect) [=] Downlink mode..... default/fixed bit length [=] Password set...... No[usb] pm3 --> lf t55xx inforesult:
[=] --- T55x7 Configuration & Information --------- [=] Safer key : 0 [=] reserved : 0 [=] Data bit rate : 5 - RF/64 [=] eXtended mode : No [=] Modulation : 8 - Manchester [=] PSK clock frequency : 0 - RF/2 [=] AOR - Answer on Request : No [=] OTP - One Time Pad : No [=] Max block : 2 [=] Password mode : No [=] Sequence Terminator : No [=] Fast Write : No [=] Inverse data : No [=] POR-Delay : No [=] ------------------------------------------------------------- [=] Raw Data - Page 0, block 0 [=] 00148040 - 00000000000101001000000001000000 [=] --- Fingerprint ------------ [+] Config block match : EM unique, PaxtonWe can see that the info gave us more information and confirmed what we decoded by hand. But remember, the detect is still needed so the proxmark3 software will know how to decode the info block.
We can see that for the EM4100 emulation we have two blocks of data (Max Block = 2). On the T5577 these will be Blocks 1 and 2.
Exercise 2
^Top
Using the skills form part 1, see if you can view the data in blocks 1 and 2.
Note: the EM4100 ID of 1122334455 is encoded, so don’t expect to see those bytes as such. To learn how to do that, you guessed it, find the datasheet and review.
At this point we have an EM4100 card. If we wanted to password protect it, we can follow the password section and update the config from 00148040 to 00148050.
Important : Don’t forget to set a valid password in block 7 and remember it.
The configuration Block – Block 3 Page 1
^Top
to be written