proxmark3/doc/md/Use_of_Proxmark/1_Validation.md at 23bcc7515a23fad1e0e37ccb782a7000a86dd195

mirror of https://github.com/RfidResearchGroup/proxmark3.git synced 2024-09-24 17:26:13 +08:00

iceman1001 bee970721c text

2021-02-19 20:38:53 +01:00

2.7 KiB

Raw Blame History

1. Validating proxmark client functionality

If all went well you should get some information about the firmware and memory usage as well as the prompt, something like this.

[=] Session log /home/iceman/.proxmark3/log_20200521.txt
[+] loaded from JSON file /home/iceman/.proxmark3/preferences.json
[=] Using UART port /dev/ttyS7
[=] Communicating with PM3 over USB-CDC


██████╗ ███╗   ███╗ ████╗  
██╔══██╗████╗ ████║   ══█║ 
██████╔╝██╔████╔██║ ████╔╝ 
██╔═══╝ ██║╚██╔╝██║   ══█║ 
██║     ██║ ╚═╝ ██║ ████╔╝     Iceman ☕
╚═╝     ╚═╝     ╚═╝ ╚═══╝  ❄️ bleeding edge
 
 https://github.com/rfidresearchgroup/proxmark3/

 [ Proxmark3 RFID instrument ] 

 [ CLIENT ]
  client: RRG/Iceman/master/v4.9237-2-g2cb19874 2020-05-21 22:00:00
  compiled with GCC 9.3.0 OS:Linux ARCH:x86_64
 
 [ PROXMARK RDV4 ]
  device.................... RDV4
  firmware.................. RDV4
  external flash............ present
  smartcard reader.......... present
  FPC USART for BT add-on... absent

 [ ARM ]
 bootrom: RRG/Iceman/master/v4.9237-2-g2cb19874 2020-05-21 22:00:10
      os: RRG/Iceman/master/v4.9237-2-g2cb19874 2019-05-21 22:00:26
 compiled with GCC 9.2.1 20191025 (release) [ARM/arm-9-branch revision 277599]

 [ FPGA ]
  LF image built for 2s30vq100 on 2020-07-08 at 23: 8: 7
  HF image built for 2s30vq100 on 2020-07-08 at 23: 8:19
  HF FeliCa image built for 2s30vq100 on 2020-07-08 at 23: 8:30

 [ Hardware ] 
  --= uC: AT91SAM7S512 Rev A
  --= Embedded Processor: ARM7TDMI
  --= Internal SRAM size: 64K bytes
  --= Architecture identifier: AT91SAM7Sxx Series
  --= Embedded flash memory 512K bytes ( 59% used )

[usb] pm3 -->

This [usb] pm3 --> is the Proxmark3 interactive prompt.

To get interactive help

For basic help type help. Or for help on a set of sub commands type the command followed by help. For example hf mf help.

First tests

These commands will return some info about your Proxmark software and hardware status.

[usb] pm3 --> hw status
[usb] pm3 --> hw version
[usb] pm3 --> hw tune

You are now ready to use your newly flashed proxmark3 device. Many commands uses the h parameter to show a help text.

To quit the client

[usb] pm3 --> quit

or simple press CTRL-D.

Next steps

Some configuration steps are still needed.

For the next steps, please read the following pages:

2.7 KiB Raw Blame History