mirror of
https://github.com/RfidResearchGroup/proxmark3.git
synced 2024-11-05 23:17:58 +08:00
148 lines
6.3 KiB
Markdown
148 lines
6.3 KiB
Markdown
# Advanced compilation parameters
|
|
|
|
The client and the Proxmark3 firmware should always be in sync.
|
|
Nevertheless, the firmware can be tuned depending on the Proxmark3 platform and options.
|
|
|
|
Indeed, the RRG/Iceman fork can be used on other Proxmark3 hardware platforms as well.
|
|
|
|
Via some definitions, you can adjust the firmware for a given platform, but also to add features like the support of the Blue Shark add-on or to select which standalone mode to embed.
|
|
|
|
## Client
|
|
|
|
The client doesn't depend on the capabilities of the Proxmark3 it's connected to.
|
|
So you can use the same client for different Proxmark3 platforms, given that everything is running the same version.
|
|
|
|
It's possible to explicitly skip the Qt support in the compilation even if Qt is present on the host, with:
|
|
|
|
```
|
|
make clean
|
|
make SKIPQT=1
|
|
```
|
|
|
|
On Linux hosts, if the Bluez headers and library are present, the client will be compiled with native Bluetooth support. It's possible to explicitly skip Bluetooth support with:
|
|
|
|
```
|
|
make clean
|
|
make SKIPBT=1
|
|
```
|
|
|
|
|
|
## Firmware
|
|
|
|
By default, the firmware is of course tuned for the Proxmark3 Rdv4.0 device, which has built-in support for 256kb onboard flash SPI memory, Sim module (smart card support), FPC connector.
|
|
These features make it very different from all other devices, there is non other like this one.
|
|
|
|
**Recommendation**: if you don't have a RDV4, we strongly recommend your device to have at least a 512kb arm chip, since this repo is crossing 256kb limit. There is still a way to skip parts to make it fit on a 256kb device, see below.
|
|
|
|
If you need to tune things and save the configuration, create a file `Makefile.platform` in the root directory of the repository, see `Makefile.platform.sample`.
|
|
For an up-to-date exhaustive list of options, you can run `make PLATFORM=`.
|
|
|
|
## PLATFORM
|
|
|
|
Here are the supported values you can assign to `PLATFORM` in `Makefile.platform`:
|
|
|
|
| PLATFORM | DESCRIPTION |
|
|
|-----------------|--------------------------|
|
|
| PM3RDV4 (def) | Proxmark3 rdv4 |
|
|
| PM3OTHER | Proxmark3 generic target |
|
|
|
|
By default `PLATFORM=PM3RDV4`.
|
|
|
|
The MCU version (256 or 512) will be detected automatically during flashing.
|
|
|
|
Known issues:
|
|
|
|
* 256kb Arm chip devices: The compiled firmware image from this repo may/will be too large for your device.
|
|
* PM3 Evo: it has a different led/button pin assignment. It tends to be messed up.
|
|
* Proxmark Pro: it has different fpga and unknown pin assignments. Will most certainly mess up
|
|
|
|
## PLATFORM_EXTRAS
|
|
|
|
Here are the supported values you can assign to `PLATFORM_EXTRAS` in `Makefile.platform`:
|
|
|
|
| PLATFORM_EXTRAS | DESCRIPTION |
|
|
|-----------------|----------------------------------------|
|
|
| BTADDON | Proxmark3 rdv4 BT add-on |
|
|
|
|
By default `PLATFORM_EXTRAS=`.
|
|
|
|
If you have installed a Blue Shark add-on on your RDV4, define `PLATFORM_EXTRAS=BTADDON` in your `Makefile.platform`.
|
|
|
|
|
|
## STANDALONE
|
|
|
|
The RRG/Iceman fork gives you to easily choose which standalone mode to embed in the firmware.
|
|
|
|
Here are the supported values you can assign to `STANDALONE` in `Makefile.platform`:
|
|
|
|
| STANDALONE | DESCRIPTION |
|
|
|-----------------|----------------------------------------|
|
|
| | No standalone mode
|
|
| LF_SKELETON | standalone mode skeleton - Iceman1001
|
|
| LF_EM4100EMUL | LF EM4100 simulator standalone mode - temskiy
|
|
| LF_EM4100RSWB | LF EM4100 read/write/clone/brute mode - Monster1024
|
|
| LF_EM4100RWC | LF EM4100 read/write/clone mode - temskiy
|
|
| LF_HIDBRUTE | HID corporate 1000 bruteforce - Federico dotta & Maurizio Agazzini
|
|
| LF_ICEHID | LF HID collector to flashmem - Iceman1001
|
|
| LF_PROXBRUTE | HID ProxII bruteforce - Brad Antoniewicz
|
|
| LF_SAMYRUN | HID26 read/clone/sim - Samy Kamkar
|
|
| HF_14ASNIFF | 14a sniff storing to flashmem - Micolous
|
|
| HF_AVEFUL | MIFARE Ultralight read/simulation - Ave Ozkal
|
|
| HF_BOG | 14a sniff with ULC/ULEV1/NTAG auth storing in flashmem - Bogito
|
|
| HF_COLIN | Mifare ultra fast sniff/sim/clone - Colin Brigato
|
|
| HF_ICECLASS | iCLASS 4-1 mode sim/read & dump/loclass/glitch & config to flashmem - Iceman1001
|
|
| HF_LEGIC | HF Legic Prime standalone - uhei
|
|
| HF_MATTYRUN | Mifare sniff/clone - Matías A. Ré Medina
|
|
| HF_MSDSAL (def)| EMV Read and emulation - Salvador Mendoza
|
|
| HF_TCPRST | IKEA Rothult ST25TA, Standalone Master Key Dump/Emulation - Nick Draffen
|
|
| HF_YOUNG | Mifare sniff/simulation - Craig Young
|
|
|
|
By default `STANDALONE=HF_MSDSAL`.
|
|
|
|
## 256kb versions
|
|
|
|
If you own a Proxmark3 Easy with only 256kb, you can use a few definitions to help you getting a smaller firmware.
|
|
|
|
First thing is of course to use the `PLATFORM=PM3OTHER`.
|
|
Adding `PLATFORM_SIZE=256` will provoke an error during compilation of the recovery image if your image is too big, so you can detect the problem before trying to flash the Proxmark3, e.g.
|
|
```
|
|
[=] GEN proxmark3_recovery.bin
|
|
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
ERROR: Firmware image too large for your platform! 262768 > 262144
|
|
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
```
|
|
|
|
You can skip the standalone support by indicating `STANDALONE=` and
|
|
a series of `SKIP_*` allow to skip some of the functionalities and to get a smaller image.
|
|
|
|
| Definitions | Rough estimation of the saved space |
|
|
|---------------------|-------------------------------------|
|
|
|STANDALONE= | 3.6kb
|
|
|SKIP_LF=1 | 25.8kb
|
|
|SKIP_HITAG=1 | 24.2kb
|
|
|SKIP_EM4x50=1 | 2.9kb
|
|
|SKIP_ISO15693=1 | 3.2kb
|
|
|SKIP_LEGICRF=1 | 3.9kb
|
|
|SKIP_ISO14443b=1 | 3.7kb
|
|
|SKIP_ISO14443a=1 | 63.0kb
|
|
|SKIP_ICLASS=1 | 10.5kb
|
|
|SKIP_FELICA=1 | 4.0kb
|
|
|SKIP_NFCBARCODE=1 | 1.4kb
|
|
|SKIP_HFSNIFF=1 | 0.5kb
|
|
|SKIP_HFPLOT=1 | 0.3kb
|
|
|
|
So for example, at the time of writing, this is a valid `Makefile.platform` compiling an image for 256k:
|
|
```
|
|
PLATFORM=PM3OTHER
|
|
PLATFORM_SIZE=256
|
|
STANDALONE=
|
|
SKIP_LEGICRF=1
|
|
SKIP_FELICA=1
|
|
```
|
|
Situation might change when the firmware is growing of course, requiring to skip more elements.
|
|
|
|
Last note: if you skip a tech, be careful not to use a standalone mode which requires that same tech, else the firmware size reduction won't be much.
|
|
|
|
## Next step
|
|
|
|
See [Compilation instructions](/doc/md/Use_of_Proxmark/0_Compilation-Instructions.md)
|